shendrones shrieker 3d models
605 3d models found related to shendrones shrieker.thingiverse
Guards for Shendrones Shrieker, arm, nose, and top guards.
thingiverse
40 degree micro fpv cam mount for Shendrones Shrieker. ...20mm tall, slide it up or down to where you want your camera, works with slammed builds.
thingiverse
An LED for the tiny Shendrones Shrieker. It fits a 32mm x 10mm LED board. They have 5mm holes for the standoffs. ...The *_large_hole versions have 5.5mm holes, incase 5mm is too tight with ABS/PLA.
thingiverse
Made for the Shendrones Shrieker 130mm quadcopter frame but should work for most frames using an 1104 size brushless motor with a 3 inch prop. Support is built into the model and can be snapped off or trimmed. ...I designed it to guard the props but...
thingiverse
I wanted to take some better video with the shrieker because its so much fun to fly. I tried a few methods of fitting an HD camera on the thing and this one is the latest. I uses a nylon screw and nut to hold the 2 parts together. The previous...
thingiverse
This lets you easily mount a Runcam Swift Micro to a Shendrones Shrieker at a fixed 30 degrees. There are 3 sizes for 25mm, 30mm, and 35mm standoffs as well as 1 45 deg mount for 25mm standoffs. ...Pictures shown are with the 25mm 30 deg version.
thingiverse
Update: Redid the whole thing. Now sits straight at the rear. Most importantly, this doesn't get your power wires caught in the props when using taller motors (1306 or 1407). Also, this way you can stick a 4-LED WS2812 square to it with sticky tape.
thingiverse
This is a part that I designed to help make mounting receiver antennas to the Shrieker. It's meant to run the antennas up through the two holes in the back, then just push a small zip tie (tapered end first) into the holes to create a tight fit. Then...
thingiverse
Not many STL's out there for the shrieker. Like to have some shoes. These snap on. Have not tested them in a crash. You may want to put a dab of glue, you may not. They seem to fit tight enough to stay on without any adhesive. Your call. The...
thingiverse
Best in TPU, pause print after 4.2mm and insert frame. ...Cam mount holds micro fpv cam with 2.3 lens, cam angles 30-60 degrees.
thingiverse
22mm between standoffs - Will also fit Shendrones Shrieker Print upside down with supports Designed to: 1) Not slide down the standoffs 2) Not allow camera to drop below 40ish degrees 3) Allow camera to tilt up as much as possible 4) Be as forward...
thingiverse
Replacement for the camera mount. This allows you to put any micro camera into the frame. Just remove the focus locking nut from the lens. The TPU nubs act to lock the lens in place. Currently I only have a 30-degree mount, but I plan to make...
thingiverse
Gopro mount for the shendrones shrieker. Use 3 rather long m3 bolts and one m3 nut. The m3 nut should be press fitted into the bottom part. Pretty self explanatory once printed. TPU or other flexible filament should make for a pretty tough mount! ...If...
thingiverse
Snap on arm guards for the shendrones shrieker. Supports are built in, and easily removed with a small flat head screwdriver. I've printed mine in PLA, 215 degrees celius and 0.1 - 0.3 layer height. Two of the guards should be mirrored in the slicer...
cults3d
My Fanwork to the dungeon and dragons Shrieker. ... You can support me on https://www.patreon.com/Schlossbauer if you like my work.
thingiverse
My Fanwork to the dungeon and dragons Shrieker. ... You can support me on https://www.patreon.com/Schlossbauer if you like my work.
prusaprinters
My Fanwork to the dungeon and dragons Shrieker. You can support me on https://www.patreon.com/Schlossbauer if you like my work. Category: Toys & Games
cults3d
Shrieker model based on the movie Terror Under the Earth 2 is part of a 5 figure set of 2 other shriekers and 2 graboids from the Tremors 2 movie, for decoration or use in a diorama.
thingiverse
the Shrieker from tremors also check out the Assblaster model here: https://www.thingiverse.com/thing:4878091 Graboid model
cults3d
Shrieker model based on the movie of Terror Under the Earth 2 is part of a 5 figure design of 2 other shrieker and 2 graboids from the Tremors 2 movie, for decoration or use in a diorama. If you would like a custom model contact my email. ... If you...
cults3d
Sculk Shrieker Block made for a Deep Dark Biome themed birthday cake.
thingiverse
A lipo protector for the Shrieker 130 frame. ...Suits 4S battery pack.
pinshape
Summary A remix of the Shrieker pod. ...Added a whale tail, enlarged the hole for the stack, and enlarged the VTX hole for standard VTXs Print Settings Printer: Wanhao Duplicator i3d V2.1 Supports: Yes Resolution: .2 Infill: 25% Notes: Printed with...
thingiverse
A remix of the Shrieker pod. ...Added a whale tail, enlarged the hole for the stack, and enlarged the VTX hole for standard VTXs Print Settings Printer: Wanhao Duplicator i3d V2.1 ...
thingiverse
This a simple mount for the HS1177 and similar cameras for tiny copters, such as the Shrieker 130.The angle is 30°. I couldn't get the metal bracket to fit without drilling and giving up space for other things, so I designed this. Use hotglue or some...
thingiverse
Simple diversity antenna mount for the Shrieker. I use it with the FrSky XM+. Made for 3mm antenna tubes and printing in TPU. The fit is very tight to make the tubes hold well. If you print it in a hard material, you may have to drill the openings a...