shockmount for blue snowball 3d models
2306340 3d models found related to shockmount for blue snowball.thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
I printed and assembled a shock mount for my Blue Yeti Microphone from Thingverse. When I tried to attach the mount to my microphone boom I needed to fill in some space. Regular washers were tricky to position so I designed one with an open bottom...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
cults3d
this is a change of the design from https://www.thingiverse.com/thing:3317197/remixes adapted to install a noise Shield on the Blue Yeti Shockmount. ...have attached all files so you do not have to search for the individual parts.
thingiverse
Here are the size of the parts if you prefer to manually scale them: W,D,H (mm) bolt.stl : 28.2, 28.2, 20 inner_ring.stl : 123.0, 123.0, 5.0 outer_ring.stl : 180.0, 180.0, 11.0 (However, scale H to 22 for stability) mick_mount.stl : 83.0, 55.8, 30.0...
thingiverse
Use this part to mount Blue Snowball to your table lamp stand.
thingiverse
I tried printing ad895's (https://www.thingiverse.com/thing:2225557) version but for the version of Blue Snowball I have the mount is too short and the hole is way to wide. When that didn't work I tried GuruX's version...
thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small footprint...
thingiverse
A small bracket for adapting the blue snowball onto the end of a swing arm lamp. Similar to This one on amazon. The Peg is slightly oversized, to allow the microphone to cut its own threads. A small bump is included on one side to help with rotation....
thingiverse
The regular Blue Snowball shock mount was huge, which made it awkward to use if you need to see past it, so I designed this tiny one that uses rubber bands for dampening. You'll need the small pipe that attaches to the microphone from the desk...
thingiverse
Needed a small form factor pop filter for my snowball mic and i didn't feel like spending 20$ on a few cents worth of plastic, print 2 of the mesh holders, glue a piece of thin fabric/mesh between them before gluing them into the model itself. ... 2...
prusaprinters
Pop filter which connects to a Blue Microphone.Add a couple layers of thin fabric will do a decent job of blocking your puffs of air.One of the securing rings has space for a 6mm inner diameter spring to help press it against the outer ring.Mounting...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
I made this simple adapter to be able to attacth my Blue Snowball to my smartphone tripod.
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
myminifactory
This is a shockmount designed specifically to fit the MXL 990. I didn't plan this, but it turns out that hair ties were just the right size to use a the elastic suspension. ...To get it to thread onto a mic stand, I had to heat the adapter part with a...
cults3d
This is my single part Pop Filter for my Blue Snowball Microphone. The pop filter can be installed easily between the tripod and the microphone bowl due to the 16mm hole. Stretch tights around the ring and press a 5mm soft rubber (or elastic band or...
thingiverse
This is my single part Pop Filter for my Blue Snowball Microphone. The pop filter can be installed easily between the tripod and the microphone bowl due to the 16mm hole. Stretch tights around the ring and press a 5mm soft rubber (or elastic band...
grabcad
This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.
thingiverse
Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
ad895 had made the design for the original nice all metal Snowball stand. I wasn't as lucky when I bought mine, and got the other cheap, partly plastic, stand. The mount needed some changes as the stands have different diameters. The downscaled...
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.