shop vac adapter 3d models
158715 3d models found related to shop vac adapter.thingiverse
Wanted to use the smaller tools from our Kirby with our Craftsman shop vac. ... Adapter allows 2 - 2 1/4 inch hose on shop vac to connect 1 - 1 1/4 inch parts from the kirby. ... Printed in PLA with 50% infill and supports.
thingiverse
A 90 degree elbow to adapt a 1.5" dust port to a 2.5" (nominal) hose, or vice-versa. ...See the build log here for more details and dimensions: http://jmillerid.com/wordpress/2012/12/3d-printed-shop-vac-adapter/ Instructions Requires support material!
thingiverse
See the build log here for more details and dimensions: jmillerid.com/wordpress/2012/12/3d-printed-shop-vac-adapter/ NOTE: this is derived from my 90 degree elbow version. ...This one is straight but uses the same fitting dimensions (see the attached...
thingiverse
Adapter Made Specifically for Bosch Shop Vac 27mm Inside Diameter Hose and a Makita 9403 Belt sander 31mm Outside Diameter. ... The walls are 1/8" thick
thingiverse
Adapts a small shop-vac vacuum hose to larger dust-collection port on power tools such as my DeWalt table saw.
thingiverse
This is an adapter for a Husky wet/dry vacuum to a Bauer Micro-Cleaning Accessory Kit. ... Specifically, the shop vac is 1 3/4" and the kit is 1 3/8". ... I recommend printing with a raft.
thingiverse
This is an adapter for small size shop vac hoses to be used with the vortex generator by Dronnn: https://www.thingiverse.com/thing:2829268 I was sanding paint and put a wrap of black tape to get a good seal, though I'm not sure it is needed. I used...
thingiverse
This is an adapter I modeled so I could attach my miter saw to my small shop-vac. the large diameter is 58mm and the small diameter is 40mm. ... I recommend printing it with support in the inside lip/transition between the two sizes.
thingiverse
Have you ever been using your Shop-Vac to clean up larger debris that ends up getting caught against the adapter that connects the hose to the collection bin of the vac? Well no more! This adapter changes the way in which the hose is held by...
thingiverse
This was made for my Shop-Vac hose to go to my Cyclone Separator. ... For some reason my Cyclone has the same size on both the input and output to the canister and my Shop-Vac hose didn't fit. ... With this, it fit perfectly.
prusaprinters
Needed an adapter to go from my 2.5" Rigid vac hose to a 1.25" flexible crevice tool I use in my car. ... Couldn't find anything, so I designed something.</p><p>Printed in PETG, no supports.</p><p>Included the .stp file, adjust as you need.</p>
thingiverse
2) Press-fit male to electrolux pipe adapter This screws onto an Electrolux vac pipe. One short section like this is required (and permanently mounted on) each tool e.g. skill saw, Router or whatever. ...This fitting is simply pressed into the above...
thingiverse
Shop Vac Adapter for home made oil extractor using 1/4" ID tubing. This is based upon the build in this video: https://www.youtube.com/watch?v=eJK92UFEIu4 (not my video) I made this because I wanted something a little more sturdy than a plastic...
cults3d
Shop vac adapter for 1 7/8in hose to Craftsman orbital sander. The adapter is friction fit to the inside of the sander dust port. The adapter also fits over the outside of the dust port to protect the channels for the dust bag. ...It also makes the...
thingiverse
Shop vac adapter for 1 7/8in hose to Craftsman orbital sander. The adapter is friction fit to the inside of the sander dust port. The adapter also fits over the outside of the dust port to protect the channels for the dust bag. ...It also makes the...
thingiverse
I welded this Ridgid shop vac adapter onto it: https://www.thingiverse.com/thing:4840182 This is a huge print. It took about 3 days. I did full supports. Not sure if you could get away with fewer supports. If so, that would save a ton of time and...
prusaprinters
Adapts the standard Ryobi sander bag connection to a 1.25" shop vac connection. Print in flexible filament with two perimeters and 15% infill to retain maximum flexibility without compromising vacuum. ...Optionally allows for a hose clamp to tighten the...
thingiverse
A hose adapter to allow a DW375 planer to be used with a 2.5-inch shop vac hose. The adapter that comes with the planer is meant to be used with a 4-inch dust collection system (the maximum volume of chips it can produce can overwhelm a 2.5-inch...
prusaprinters
Designed as a print-in-one part for allowing a Dyson cordless vacuum to be used for dust extraction as a shop vac (eg as a lighter-weight alternative for extracting dust while sanding paintwork etc) or used to connect standard vacuum accessories.The...
thingiverse
These adapters allow my small shop vacuum to connect to ports for dust collection. ...Your mileage may vary.
myminifactory
These adapters allow my small shop vacuum to connect to ports for dust collection. ...Your mileage may vary.
thingiverse
A simple adapter that allows a "standard" de-soldering pump to be connected to a shopvac.
thingiverse
Shopvac / Vacuum Adapter / Coupler / Reducer fits on a 45mm and reduces to 16mm https://www.buymeacoffee.com/jschaftenaar https://paypal.me/jschaftenaar
thingiverse
This adapter will allow you to connect one of several Makita sanders to a Shopvac with a 1.25" hose using the connector section of the dust bag. Fits flawlessly, and gives a nice tight seal. I use it with a BO5041 5" random orbit sander, but their...
thingiverse
This is a Shop Vac Hose Adapter that I designed with a 2" OD on one end and a tapered 2.2"-2.4" OD on the other end. I bought a 20' shop vac hose from Home Depot and cut it in half. The cut ends were just the bare hose. The 2" end of the adapter...
thingiverse
Customized version of https://www.thingiverse.com/thing:3819146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3819146
thingiverse
Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651