shotgun shell holder 3d models

A 8 shotgun shell holder with molle back straps. ...

Picatinny Rail Shotgun Shell Holder

Shotgun Shell Holder Benelli M3

This Holder is designed for shotgun shells, but it can be used for anything. ...the smallest hole on the side is meant for eye protection

A holder for Tokyo Marui style shotgun shells. ... Just print it out and stick it to the side of your gun to hold spare ammo.

A simple solution for holding loose .410 shotgun shells on a safe door. ...Print Settings Printer: A8 clone Rafts: ...

Rail for holding 6 airsoft shotgun shells and primary designed for the Tokyo Marui KSG shotgun but should fit other airsoft shotguns with a 22mm rail. You will need 2 x M3 screws about 15mm long to attach the rail. Print Settings Printer Brand: ...

A prototype 3D printed Shogun shell holder for loading 2 shells at a time. ...Good for finding the correct placement of shells, spacing of holder, and angle of holder to make a better assessment of this technique before purchasing equipment.

designed this shell holder to be more sturdy than some of the other clip-in type models. ...firmly holds in 12ga shells with minimal effort to snap in, but with enough strength to keep shells from falling out

Holds standard box of 12 gauge shells for Trap or Skeet

Put this together for holding 12Ga. ...shells in the duck boat without having to dig for them. ... Just updated, aligned mounting holes and cleaned up the ends a little.

... PLA. The barrel has a tight fit and the shell holes might need a little boring on the bottom part but its fine. ...I ha to do way more for this one.</p> <h3>Print instructions</h3><p>.15 layer height</p> <p>supports touching build plate only</p>

20 Gauge Shotgun Shell holder to attach to your sling or belt.

I created another shotgun shell holder (thing:2434154) but needed a few very fast(!!!) for the weekend. So I started designing one which can be attached with velcrotape to the belt. This thing costs with black ABS about 0,16€ (0,19$) and is printed...

12 & 20ga Shot Gun Shell Holder for your belt. ... Each print holds 5 shells

Remix of "shotgun holder for 12ga by juan_bear" I was asked to print his design for airsoft shotgun shells, but upon inspection the holes were too small for an airsoft 30 round shell. I resized his model and made the back part thicker, mainly as I...

I have my 20 gauge shotgun for home defense near my bed and some shells for it in my nightstand rattling around. I wanted something simple to hold them upright and in a consistent location to be able to quickly grab if needed. This could easily be...

I don't like having shell free in my vest's pockets so I designed these holders that snap together and attach to a backpack's strap. The shells I use hold well enough in place (i.e. won't fall freely) but they're easy to pull out if you need to. You...

I don't like having shell free in my vest's pockets so I designed these holders that snap together and attach to a backpack's strap. The shells I use hold well enough in place (i.e. won't fall freely) but they're easy to pull out if you need to. You...

This is an improvement on my previous holder. ...It is still meant for a 12 gauge box and the smallest hole on the side is for holding eye protection.

Shotgun shell holder to slide on your belt for 4 additional shells.

Fits 12 GA shells. ...Fits up to a riggers belt. The grip on the shells and belt is good. Updated a lot of small details and I'm happy with the results. This is the final 5 shotgun shell holder.

No raft or support needed. I used infill of 10% and lines at 0.1. ...It was a long print but it looks great.

you might need longer screws to attach it

This is a 12 ga shotgun shell holder. Holds 10 shells. Low profile. Fits up to a riggers belt. The shells are snug. Vertical draw. ...Fast print.

this is the 12 guage shotgun shell holder you can use in conjunction with the long link, this is the short link

Thing I made for IPSC shotgun competition to make 9 shells before entering stage

IPSC Shotgun holder for up to 12/76 shells Used official technical specifications of the legal information system of the Republic of Austria and included the tolerances. So if your 12/60-76 shells are within that tolerances they should fit. ... If you...

Remix of https://www.thingiverse.com/thing:4970688 Turned it into a side saddle for a 12ga shotgun. Can be mounted with velcro, like other side saddles. Added 5 shell and 6 shell versions. Prints well, no need for support. ...Recommend 4-6 walls...

This M-Lok compatable shell holder holds 3x shells in the vertical position. Included is the step file incase you want to edit/remix. ...I specifically made this for airsoft but it can be used for real-steel.<br><br>Recommended filament: PETG</p>