side rail mount 3d models
535945 3d models found related to side rail mount.thingiverse
Made a side rail mount for a airsoft SVD Dragonov. I only printed the two lower versions in the picture. Tested it on a CYMA SVD. The scope version will bend if you put a sight or scope that is too heavy for it. ...Print with it on it's back and use...
thingiverse
Made a AK type side rail mount to be used with a red dot type sight. Tested it on my AK74U, used the groove on the top to see if it's lined up with the sights on the AK. This is just a early version I will make different versions later on. Print on...
thingiverse
Kalashnikov picatinny rail to mount on original AK side rail It was closely calculated so that everything fits exactly! but may need to be reworked due to large differences in the AK47 - production !!! UPDATE !!! ...Please use grub screws to fix the...
thingiverse
Well my webcam died and I put in a new IP camera, this camera was a lot bigger but moves so it allowed me to view the control panel progress along with the print, but it got in the way on my desk, threw this together to mount in the rail on the left...
thingiverse
Added threaded holes for top Trigorilla Top Custom2_4 added tiny hole for fan wire to go through, added threaded holes to match bottom Update List: adds to holes to side to vertical mount on rail made bottom piece slightly smaller as didnt fit before...
thingiverse
Lightweight mount for an Octopi that mounts to 2020 or 2040 rail. Can be mounted on the left or right or whatever. The back is thin on the original for a faster print but it is fairly flexible which may not be what you want if using with a...
thingiverse
I needed a raspberry pi 3b mount for my ender 5 to use octoprint and found one but my print head kept running into it so i remixed the file to be a side rail mount. This keeps it out of the way of all moving parts. Remixed from:...
thingiverse
... not threaded where the LCD would normally mount on the v1 and Pro models. So I created this mount that mounts on the side of the rail instead. ... Use M3 bolts (10mm or so) and these v-slot nut adapters: https://www.thingiverse.com/thing:3050607
thingiverse
just got a double bell Kar 98K shell eject gas version this mount is designed for no tapping/ screws, just slide it in and it's good to go. since there're no recoil on this the friction works good enough for me. ... the drawing itself leaves some...
thingiverse
Requires M5 hammer head T-nuts and M5 bolts to fasten to frame. ... Center hole in top can be used to affix whatever you like to the bracket.
thingiverse
M5-sized connection to the TAZ, provides M4-sized connections to whatever you are mounting. Has an M4-sized center hole to easily mount things that you want centered, as well. Print Settings Printer Brand: LulzBot ...
thingiverse
This is a remix of the mount from @artworkvideo but with the T-nuts supports in the side for those who don't want to remove the original front rail cover or have the mod for front power button like me. I published the part for left and right side if...
thingiverse
This will attach directly to the bottom of the splashproof HDR-AZ1 and provide Contour T-Rails for left side mounting. ...It is left side only so that access to the battery door is not blocked while installed.
thingiverse
I mirrored the right side mount to work on the right side per request.
thingiverse
Higher rail for parrallel use of side und top rail. ... Remix of : https://www.thingiverse.com/thing:5267291
thingiverse
Slides into the rail on either side of the printer The stl is set up for the left side of the printer. Mirror it over the correct axis in your slicer if you want it on the right side. The image is of the mirrored version as I use it! ... Zip tie...
thingiverse
I was trying to avoid using as much hardware as possible, specially the specialty bolts so I removed the screw mounts and added a 2020 rail using FreeCAD. I only ended up needing to edit the Bottom part of the case, also called "Case_Front.stl" in...
cults3d
Depending on how tight you get the screws to mount it should fit nice and snug, however if you wrap the back of the light or the mount with a little tap you should have a nice snug mount. the Olight has two light modes. low isn't very bright. ...
thingiverse
Depending on how tight you get the screws to mount it should fit nice and snug, however if you wrap the back of the light or the mount with a little tap you should have a nice snug mount. the Olight has two light modes. low isn't very bright. ...
thingiverse
If you can't mount your flashlight straight above the rail, this side mount should help you with keeping more accessories in a crowded space - like in my example, where the scope occupies the full length of the rail and flashlight has to be...
thingiverse
Needed a good looking way to mount a NI power supply sideways. ...This recessed holder looks nice and helps to hold the power supply in a sideways orientation.
thingiverse
Printed with PLA and fits nicely on the remote.
thingiverse
Odroid U3 DIN rail mountable board (side mounted version). Convenient and small design, suitable for mounting your development board within a network rack. Need to customize? No worries, I included all files: FreeCad (FastenersWB plugin required),...
myminifactory
This mount is built to attach to the side rails of your Nerf Rivals toy. To attach the mount to the Rivals Picatinny rail use a M3 Nut and bolt. The Go Pro Mounts up with the same sized nut and bolt. ...This mount can be used either side of the Rival...
thingiverse
E3D hemera mount for linear rails with 20x20mm hole spacing, 5015 radial fan V1_Mounts Was mount was designed for Ender 3/3 PRO with the 3DFUSED X gantry conversion with MGN12H Carriages (but will fit other printers with the same rail system/setup)...