sidewinder x1 filament guide 3d models

Ich brauchte einen vernünftigen Sensorhalter für den X1 und meinen Genius... Gebaut habe ich diesen. Stabil in der Verschraubung über 3 x M3 Schrauben und Hammerkopfmuttern. Der Sensor liegt Stabil in einer Ausbuchtung und wird durch den Halter...

A case for the Raspberry Pi to attach it to the Sidewinder. I use it to run Octoprint and a camera module. For a fan, I used this one: https://shop.pimoroni.com/products/fan-shim?variant=29210095812691 (for this the spacer in the area of the...

Specifically to include a mountpoint for a flatcable clamp. There are other similar designs but I did not like them enough so I build this one. I printed with a lot of supports to keep the outside nice. Alternatively you could orient it with the...

... Alternatively you could orient it with the sidewinder side on the bed. You choose. You may need to screw in the nut and bolt and if the nut does not fit exactly use a soldering iron to push it in the plastic. ... Category: 3D Printer Accessories

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

... just as bland, so I decided to create a brand-new one that would allow for more airflow and a bigger cable slot since I had added a 3D Touch. ... The result is a motor cover that fits the X1 perfectly. ...Its honeycomb design gives it a unique look.

Filament protector for Tronxy X1 printer, also shields filament from abrasive Z axis movement.

Update - 04/09/2024Redesigned the complete model from scratch because some "friendly" user notified me of possible flaws in the design.Repositioned the holes (in sled as well as the filament guide) and made them a bit smaller (sled) to fit the Ruthex...

Decided the Z rod brackets on the back of a Sidewinder could handle a few more grams of load so I hammed this plate together to press fit on it giving you a build platform that can utilize these bits: https://www.thingiverse.com/thing:3114849Example...

Obviously it is a remix of skartz's Sidewinder side mount, but I swapped out my camera for one that didn't have left to right swivel and OctoEverywhere was missing errors because it wasn't at an ideal angle. To make this work for my new camera, I...

Inspired by mauditfou's SWX1 Side Bed Chain, https://www.thingiverse.com/thing:4710423, I rearranged my Sidewinder's heatbed to the side, and, created this chain of vertebrae to protect the cable. Works great! The base cover in the photo is a...

Now, the Sidewinder operates silently during idle mode, and the fan only spools up from 30% speed when the Steppers exceed 35 degrees Celsius, gradually increasing to full speed as needed. The Temperature Probe utilizes the Extruder Stepper for...

I've attached both the Cura 4.2.1 profile and the g-code directly, allowing you to print the design on your Sidewinder artillery using PETG if your nozzle is 0.4 mm in diameter. ... Moving the tensioner as close as possible to the Z axis while...

https://www.youtube.com/watch?v=lBemrqoUbdc&t=15s ---------------------------------------------------------------------------------- Esta es una montura para el Hemera en una Artillery X1 (es probable que sea compatible con la Artillery Genius) La...

... the old holder on the backside, but mounting it on both sides provides greater stability. I recommend using 5mm T-nuts with 10mm long screws. This custom spool holder is not limited to the X1; it can also be used on other 20mm extrusion machines.

https://www.youtube.com/watch?v=lBemrqoUbdc&t=15s Esta es una montura para el Hemera en una Artillery X1 (es probable que sea compatible con la Artillery Genius) La montura no necesita soportes, es ideal imprimirla con PETG, ABS o ASA. El modelo...

Auto bed levelling mounting options for either a Touch Mi or BLtouch. ...Easy to print and install with free pre-configured firmware and a video guide: https://youtu.be/V3zEJGOcz7s

Insert guide tube back into extruder pressure lever from top, pushing it all the way down until top of tube is even with flat surface of middle hole of adapter. The tube locks adapter in place. You may have to trim guide tube if it's a little long,...

- This is an adjuster add-on for the Artillery Sidewinder spool holder. - It keeps the spool holder frame fixed in place by pressuring the locking nuts. - Pressing between the two screws will enable the spool holder frame to slide. -...

The stock spool holder that comes with the x1 isn't the greatest. For me it caused just a bit too much resistance, pulling the extruder up ever so slightly and thus some layer variation.</p> <p>So I made this with two options that can be easily...

... be removed without taking apart the entire system. Design Highlights: Cool, well-designed reinforcement. Specifically made for X1 v4 printers. ... Screws Required: - 4 x M5x30 Hex Head - 6 x M5x30 Flat Head + 6 Nuts - 4 x M4x80 (Hex or Flat Head)

If you want to purchase the fan I leave the video where he explains improvements and directs you to the store.https://www.youtube.com/watch?v=lBemrqoUbdc&amp;t=15s-------------------------------------------------------------------Esta es una montura...

for artillery sidewinder x1**NOTE** don't waste your time if you do not have a sufficient supply of fasteners! ...i happen to sell them for a living :D

The stock spool holder that comes with the x1 just doesn't cut it for me. It causes a bit too much drag, pulling the extruder up ever so slightly and resulting in some layer variation. So I created this with two interchangeable options on the main...

Take a look at my other sidewinder X1 upgrades: https://www.thingiverse.com/thing:4784042 Artillery Sidewinder X1 Extruder Cover V4 w/ Strain Relief https://www.thingiverse.com/thing:4783250 Artillery Sidewinder X1 Left X Cover with Cable Strain...

Remodeled skartz's bracket to accept a Raspberry Pi camera by remixing it and using Fusion as a guide, resulting in a version with slightly different dimensions but still retaining its basic shape and not obstructing the print bed when fully...

... snaps into place within a corresponding hole in the aluminum plate, which is rigidly connected to the heatsink assembly. To minimize thermal distortions, it's essential to use PETG or other high-temperature filaments when printing with this setup.

I started using Prusa Slicer a lot more in the past few weeks with great results so i thought i make it look better. For each of my printers i added a custom build plate. This improves looks and it also makes it easier to see what printer i am using....

... if it was really good) and printer vibration are normal. **I have too add a PTFE tube just to remove the friction between the filament and the box.** Fastener required: ***4x M5x8 Screw (back)*** & ***2x M5x12 Screw C/W 2x M5 T-Slot Nut (front)***