sidewinder x1 filament guide 3d models

The stock spool holder kept the filament tight due to the drag and would cause problems with my prints. This one changes it to an axle and bearing setup rather than the coaster type. This is a very simple but effective upgrade for your printer. It...

Relocation of the filament sensor is a critical step when transferring the spool to the top of the 3D printer. ... Built from the ground up, this design takes its cue from a pioneering project on Thingiverse: https://www.thingiverse.com/thing:3913591.

... designed to attach the top of the frame to the legs of a Ikea lack table. ...Included a redesigned filament detector bracket attached to the upper frame. You need to print one "Renfort G" and also one mirrored for the right hand side. ... Enjoy !

I designed an easy-to-make mount for my eSUN filament dryer, replacing the stock spool holder completely. The new design also eliminates the need for a runout sensor since I don't use it. ...To add some extra visibility, I created a slot to slide in a...

... designed to attach the top of the frame to the legs of a Ikea lack table. ...Included a redesigned filament detector bracket attached to the upper frame. You need to print one "Renfort G" and also one mirrored for the right hand side. ... Enjoy !

Designing a stand-alone support for the filament roll reduces weight at the top of the crossbeam on the vertical rack. The side plates can be printed in either a vertical or horizontal orientation. For optimal results, print the rolls vertically. The...

Even if they work, the lever applies pressure to the filament, but under no circumstances should it guide the filament with a piece of PTFE (moving). Why? the PTFE tube (black tube stuck in the lever) follows the movement of the lever, if we...

I utilized M3 drop-in T-nuts found at http://www.thingiverse.com/thing:3050607 to secure three guides to the printer, while the main guide employs an M6 PTFE coupler. Initially, I used an old coupler from my Ender but replaced it with a new one...

Did not like the guides i found so i made it myself.It's in 2 parts so you don't have to take anything apart.

Go through these prints in this order. Do not move on to the next step until you are happy with the print of the step that you are on. 1. DIY Bed leveling square 50 100 150 200 250 Goal, make sure that lines are not lifting when they print. ...

Accessoire pour Sidewinder X1 permettant d'éviter l'éventuelle chute de la bobine de filament . Accessory for Sidewinder X1 to prevent the possible fall of the filament spool. ...

Bedlevel Test Sidewinder X1

This is my new filament guide to remove the spool holder form the top of the gantry of the sidewinder X1 If you are running the Sidewinder X1 - Z Brace by Double_Mirages it will help as I run the PTFE tube through the brace. ... See photos.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

this design is a customization of https://www.thingiverse.com/thing:4051490 I have modified the design adding better ones to my liking. you now have a socket to hold the sensor cable. The artillery logo has been added. The bracket for mounting...

I have modified the design adding better ones to my liking. you now have a socket to hold the sensor cable. The artillery logo has been added. The bracket for mounting m3 socket nuts and bolts has been redesigned. ... I hope you like it.

Print, insert a piece of sponge and enjoy. The first time it may be difficult to open the cover. ... Be careful, light sanding may be necessary.

For this reason I created the little Filament guide that prevents that the filament can jump of the pulley while the Z Axis or spool is moving. A 3cm PTFE Tube is needed and the bore should be drilled that the PTFE Tube fits snuggly. ... Fusion 360...

Sidewinder X1 Mounting System for Pinda Equipment.

Support de bobine filament avec capteur fin de fil pour la Sidewinder X1.En complément de l'objet: https://www.thingiverse.com/thing:3650974

Support de bobine filament avec capteur fin de fil pour la Sidewinder X1.En complément de l'objet: https://www.thingiverse.com/thing:3650974

Artillery Sidewinder X1 (V4) Wyze Camera Side Mount (Snap Fit).

Support GoPro pour sidewinder X1, pour surveiller les impressions.

Cover the Sidewinder X1 on your left side now.

Sidewinder X1 Squashball - foot. ...To stop passing on the vibration to the table and so on.   

Sidewinder PTFE cutting jig x1 45 mm with a cutter blade.

kit d'adaptation pour barre led OMLOPP ikea sur sidewinder X1

Salut la communauté, J'ai créé ce guide qui s'adapte sur le système de bobine latérale de Wheesir, j'ai voulu améliorer le guidage du filament sur le support de bobine latérale de ma SideWinder X2, Ce n'est pas grand-chose, mais ça évite que le...

This is a simplified version of the "Artillery Sidewinder X1" in STL format for easy use with Blender. ...Originally taken from "https://grabcad.com/library/artillery-sidewinder-x1-1", I converted it to *.stl format for further processing.

Nozzle Cleaner for Artillery Sidewinder X1 https://de.aliexpress.com/item/33053117369.html?spm=a2g0s.9042311.0.0.295f4c4d53D7Ym