sidewinder x1 filament guide 3d models
274133 3d models found related to sidewinder x1 filament guide.
thingiverse
I'm attaching a frame brace for my X1 printer. My V4 printer is what I'm using, so I can't confirm if this design will work with other versions or not. The top parts are attached to the printer with M5 T-nuts and M5x10 screws. The bottom part...
prusaprinters
Bolt and Nut M3 13mm 2X M3 18mm 1X M3 20mm 1X M3 Nut 4X Screw head no higher than 2 mm M3 5,8mm 1X M3 3,7mm 1X Print instructionsSupports: No Resolution: First layer 0.3 and the remainder 0.2 Infill: 25% Filament color: Black Filament material: PETG
thingiverse
The filament sensor now has a small holder to attach to. This allows the sensor to move freely and stay centered. You'll need one additional M3 screw and nut for this setup, but you can reuse the other two from the original design. ...Be sure not to...
cults3d
just a small holder for the filament sensor now the sensor can freely move and is also more centered you need only one M3 screw and nut extra, take the other screw and nut thing from original don´t tighten the sensor too much, so that it can freely...
thingiverse
I designed a straightforward bracket to attach the filament sensor on the Y axis, allowing me to utilize identical Z endstops and eliminate the sync belt altogether. To secure the endstop in place, I tightened it with two small zip ties, then...
thingiverse
... I made sure everything was aligned properly before tightening all the screws. I have two different configurations to work with here. In one version, I need to adjust my setup slightly higher due to my filament box and cleaner being in the way.
thingiverse
This is a fairly thorough and accurate guide to installing the BTT SKR 1.4 / 1.4 Turbo board into your X1, utilizing the existing stock screen and LEDs. In this guide you'll learn how to replace hardware and update your firmware for the new board...
thingiverse
+ Recreated the Knob, as the original design is hard to turn and hurts the fingers, therefor i wanted to create one where you can easily make preasure without getting hurt ;-) + Removed the logo and redesigned the front so that it fits better with...
thingiverse
Also, there is a slot for the filament sensor that comes with the printer to be put in place so you don't lose that functionality this is NOT a Bowden extrusion adaptor You will need a bit of PTFE tube to guide it and that is all Optionally if it...
prusaprinters
Therefore I cut out a channel to guide those wires securely behind the hemera to the board. That way it looks clean, and you don't risk your wires catching on some prints or melting on the heater block. Print Settings Printer: VoxelONE (custom)...
thingiverse
... with my BLTouch and Hemera fan. ...Therefore I cut out a channel to guide those wires securely behind the hemera to the board. That way it looks clean, and you don't risk your wires catching on some prints or melting on the heater block. ...
thingiverse
Remixed to match the look of the other design (tube/filament guide), just used the "clamp" part. ... Printed a pair of tube guides because my spool sits on the table near the printer, not on the top.
cults3d
No me vale el original, lo he hecho mas largo para tener marguen. https://www.thingiverse.com/thing:3972011 The original is not worth it, I have made it longer to have marguen. ... https://www.thingiverse.com/thing:3972011
thingiverse
https://www.thingiverse.com/thing:4919346 No me vale el original, lo he hecho mas largo para tener marguen. https://www.thingiverse.com/thing:3972011 https://www.thingiverse.com/thing:4919346 The original is not worth it, I have made it...
thingiverse
This is designed to screw into the stock filament sensor of the Sidewinder X1 and allows PTFE tubing to attach to the mount. Use a PC4-M6 pneumatic fitting (5mm thread) to anchor the PTFE tubing to the mount, which screws into the sensor. This...
thingiverse
Simple end filament sensor holder for Artillery Genius and Sidewinder X1 You need one M3x10 bolt and one M3 nut to fix it Support fin de filament pour Artillery Genius et SWX1 Une vis M3x10 et un écrou M3 sont nécessaire au montage
thingiverse
This is a deported filament spooler for my Artillery Sidewinder X1. It's based on a 608zz bearing, You can attach it on a tube of 20mm diameter. Use M4 or M3 to attach it. (holes can accept M3 and M4 with nuts). The fusion 360 file is...
prusaprinters
This is a deported filament spooler for my Artillery Sidewinder X1. It's based on a 608zz bearing, You can attach it on a tube of 20mm diameter. Use M4 or M3 to attach it. (holes can accept M3 and M4 with nuts). The fusion 360 file is included if you...
thingiverse
Update 03.07.2023 For the filament deflection you will find a version 2 with deflection roller for better feeding of the filament at: https://www.thingiverse.com/thing:6107193 A suitable filament spool holder for 0.25 kg to 4.0 kg spools can be...
thingiverse
Since I had problems with a very rough filament and it came to higher friction in the PTFE tube, I have created a version with a deflection wheel for less resistance during filament delivery. For the assembly you need - 2x screw M3 x 10 cylinder...
thingiverse
Remix of https://www.thingiverse.com/thing:5030165 With https://www.thingiverse.com/thing:4821342 Thanks for the original.