sig p365 pinky extension 3d models
31780 3d models found related to sig p365 pinky extension.thingiverse
Added a flat base plate and the sig logo to both. ...Not my design, just added some minor tweaks.
thingiverse
Here's the pinky extended remix of fiftystiff's flush baseplate. Unfortunately, I could not figure out how add stippling/knurling in Fusion 360. Enjoy! I printed this laying down flat, I have uploaded a revised STL with the model flat on...
cults3d
SIG Sauer P365 Mold for holster making, tried and tested for leather holster making Features sight channel and clearances that makes leather holster making and wet molding simple and effective
grabcad
This is a base pad for the Sig P365. I designed and toleranced it to be 3D printed in Nylon. Use it as a platform for your own wacky hand configuration or to play with more ideas! Also included is the FFF file for Simplify3D I'd used to print it.
cults3d
The P365 magazines are notoriously difficult to feed rounds into. This mag loader makes it so much easier! It is based on my other designs and optimized to function with the P365 mags. ...It's a simple print and once you use it, you'll wonder how you...
thingiverse
A magnetic magazine carrier for p365 steel magazines. should be compatible with any steel magazine with a width of 32mm or less Requires two magnets, one 8mm and one 20mm with 5mm center hole. The two parts are printed separately in ABS and then...
thingiverse
This speed loader is for a SIG P365. ...Used supports and 50 percent infill.
thingiverse
This is a magazine insert for a Sig Sauer P365 magazine. ...Don't shoot your eye out.
thingiverse
This is a replacement part for the baseplate of the magazine for the Sig P365. My dad wanted to replace the pinky extended one with the standard end, but he didn't want to buy a whole other magazine, so I built this model from scratch based on the...
thingiverse
A simple mount or holster for the Sig Sauer P365. Can be mounted almost anywhere with just a couple of screws. May be a bit of a snug fit at first but I used a to soften it up a bit and mold it too my gun. Please let me know what you think! ...Also,...
thingiverse
Tried RockyMtnMark's Picatinny rail for the P365, and wasn't a fan of how low my flashlight was mounted when using it. The extra height was needed to allow for the screw and nut mounting hardware. But I found that the clamping force from my Olight...
thingiverse
... put the downward pressure point from the UpLULA as far to the rear of the magazine as possible. It's especially useful for loading mags that have pinky extensions, i.e. ...that are not flat-bottomed, keeping the mag from rocking back in the UpLULA.
thingiverse
... one. ... This is a remix of alfsauve's remix of ZacharyC3P0's Sig Sauer p365 Magazine Pouch. I took alfsauve's design, threw it into Tinkercad, put two of them side by side and filled in the gaps. Very technical, much design. ...Test print is underway.
thingiverse
... ...TWO magazine holders! This is a remix of alfsauve's remix of ZacharyC3PO's Sig Sauer P365 magazine pouch. I took alfsauve's file, threw it into Tinkercad, put 2 of them next to each other and filled in the gaps. Very technical. ...Much design.
thingiverse
Purchased a new Sig Legion P938 and the pinky extender isnt long enough for my slightly larger hands.. I used a SOL scanner, then brought the STL/OBJ into Sketchup and added the bottom to it.. Then into MeshMixer to fix a few minor holes, etc.. ...
thingiverse
Mag Extension that fits the Sig p365xl. I found a few that just didn't quite fit so I had a trim it a bit but it fits great now. The hole was a bit tight either by design or from elephants foot but I put a 5mm drill bit through it and it was...
cults3d
Mag Extension that fits the Sig p365xl. I found a few that just didn't quite fit so I had a trim it a bit but it fits great now. ... The hole was a bit tight either by design or from elephants foot but I put a 5mm drill bit through it and it was...
thingiverse
**P365_AccessoryRail_Flash-i1R-EOS** (Original) This is a flashlight mount for the *Sig Sauer P365*'s proprietary accessory rail. It is designed specifically for the [Olight i1R EOS](https://olightworld.com/olight-i1r-eos) LED keychain flashlight,...
thingiverse
Please comment with your attempts so others can learn. Measure your magazine at its widest points along the top 6 cm of the magazine: - Front to back (P365: 32 mm) - Side to side (P365: 20.5 mm) Quick math will give you percentages to resize by in...
thingiverse
No problem as the smallest mag for the P365 is 10 rounds. However, in order to improve magazine ejection if a little force can be added to the magazine follower where it presses against the slide stop then magazine changes could be faster. By...
thingiverse
Added mag holders to this popular design, its company and keeps things in line where its needed. I printed this in 0.15 layer heights but 0.2 will work just fine. ... Remixed from - thing:4245109
thingiverse
For use with "ADE Advanced Optics IWB Holster for Sig P365/P365 SAS/P365X/P365XL" . ... I purchased the holster from this link: [https://www.amazon.com/gp/product/B09KNZ1GC6/](https://www.amazon.com/gp/product/B09KNZ1GC6/)
grabcad
special thanks to thinkin3D as the top body, the follower, insert, and floorplate were taken from his sig p250 design. ...the extension part is basically the top body copied twice to in theory triple the capacity, could hold maybe 36 rounds if i had to...
thingiverse
This pinky extension fits all compact and full-size magazines. It will not fit the subcompact magazines. You will need a very small file or pick to clean out the grooves from the supports needed to print the slots the magazine rails slide into. ... In...