simple boat 3d models

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

 - Click on the "Download" button and you will find the download file in small print coloured light grey below the Model  files. Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

...Please check if they are valid for your model.Choice & file prefixesABCDcap typeFXFXSFXEplainAAAbelt tensionBBBtyre inflationCDDall cap variants use the same gasketgasketGGGFitI have printed two dozens of variants during development of the caps.

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I have completed the task, which is an intricate and comprehensive model. It required two full weeks of my time. I eagerly anticipate your appreciation for it; have a great day! :) :)</s> щ поставих задачата, която е детайлна и обширна конструкция. Я...

&nbsp;You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid. &nbsp;This can be...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I considered adjusting the model, but decided to leave it as is. I'd rather have a more positive engagement that you can adjust to your liking, than end up with one that doesn't latch in place securely enough. ;)</p><p>I will leave this marked as a...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

To do this, I will add the foot models in STEP format, they are easy to edit. Assembly video: https://www.youtube.com/watch?v=zzjLTr3RoPg https://www.youtube.com/watch?v=Tg764du-zTU https://www.youtube.com/watch?v=Vcvz-GSpdps With a 3S...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

...Composed of two pieces - a base for the motor and a cover - the protector fits perfectly on your pistol model, keeping your magazine safe and protected throughout the action. Don't let a lost magazine ruin your play - get our magazine protector now!