simple speaker 3d models
276110 3d models found related to simple speaker.thingiverse
Simple speaker box for 9 cm loudspeaker. ... Design is open and available on https://cad.onshape.com/documents/0603b028a2079f9491ba22eb/w/27c16f60f367207522684a4e/e/60990822d34cb0ce1137fbbf M3 brass knurl nuts -...
thingiverse
I was looking for some simple speaker wallmounts for my 5.1 setup, but as I did not find suitable items, I created some by myself. ...
thingiverse
# Simple Speaker Stand My brother asked me to design a simple speaker stand for his desktop speakers that would provide some clearance from the desk and incline them to face slightly upward. Some felt pads were added to the model as a soft interface...
myminifactory
These are just a simple 10 degree speaker stands that I knocked up. ...
thingiverse
Was looking for a simple base to tilt a pair of desktop speakers sitting on a dresser. These are sized to suit an ELAC B6 but could easily be scaled for something different. ... Tilt angle is 15 deg.
thingiverse
I was wanting a simple stand for my desktop monitors to angle up a bit. ... This one is 10 deg incline. The spacer was provided because the back brace was just a bit far back for my small speakers (Edifier R1010BT - $62 CDN on Prime Day)
thingiverse
I needed a speaker holder for a 8 ohm speaker with a 33mm ring to clamp the back magnet.
thingiverse
Only one 4mm screw and one 5mm dowel is needed for mounting it to the Wall, which should be more than enough for most satellite speakers. In my case i'm pretty sure the plastic will break long before the 5mm dowel gives up.. To connect the two parts...
thingiverse
I made this for 2 speaker that i had laying around, so you can also mount smaller speakers when you modify the speaker mount. The full printet speaker grid is just a prototype, i dont tried to print it until now. ...The white metal grid was a leftover...
thingiverse
Just some super simple 4-inch speaker box I made in inventor. There are no screw holes, you must drill them yourself. I used Apoxie Sculpt to attach the back panel to the box. ... I'm not sure if the speaker hole itself is exactly four inches,...
thingiverse
This is a simple speaker grill I coded in 1 hour, because I needed one. ... NOTE: works only for speakers with even numbers of screwholes!
prusaprinters
6-10W small simple speaker Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Doesn't Matter Resolution: 0.2mm Infill: 20% Filament: noname PLA Wood color Category: DIY
grabcad
It was made in a school project where I was to disassemble a old radio and measure the inner components. It have a diameter of 77mm and the model is made in Rhino 3d. I have tried to upload in some other formats as well. ... (It is a little rough)
cults3d
... new speakers that were a LOT larger than I anticipated. ...Didn't have room on the desk, so I decided to mount them on top of the monitor. Built for speakers 60mm deep with a 10° pitch (FreeCAD files included for customization) Some Assembly Required
thingiverse
Built for speakers 60mm deep with a 10° pitch (FreeCAD files included for customization) Some Assembly Required Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.30mm...
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348
thingiverse
Customized version of https://www.thingiverse.com/thing:3834348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3834348