simplify3d petg profile cr10

Cr10 s z axis aligner, its a simple tool to hold your Z screw in place while you align the stepper motor. Use an X axis bracket to hold the whole x axis level in place, near the bottom of the frame (loads on here) clip this bracket to the top of...

I designed it to fit seamlessly on the CR10 control box, replacing the standard spool holder entirely. The bracket(s) can be easily moved to accommodate any width of spool roll with absolute precision. I added rubber pieces to grip the box...

When working directly beside the CR10 V2, the noise level is unacceptable. I liked the solution from SIGANBERG so I copied it. I thank you for the idea! The fan housing inside did not fit as the original fan is mounted on bushes. By simply bolting...

The good news is your new iPhone is safe. ...The bad news is you have to print with PETG.

PETG Tower Temperature Range: 230-250 Degrees Celsius, Layer Height: 0.2 Millimeters, Fill Density: 15 Percent.

..... ...here is a packaging made of PETG plastic - for the automatic dispensing of candied, pickled fresh fruits ....step, igs, stp

Prefer working over 70°C 3) Move motors and electronics outside of enclosure 4) Use as much of my existing printer frame as I can Here's a list of modifications over the original CR10 (only the rails are really necessary, you could use the original...

It securely attaches to the top bar of any profile. This innovative design is an enhanced version of the original tool I created for my own personal use. ...If you have faith in your printer's bridging capabilities, you can confidently print without...

... broke. I printed it with petg, 4 walls, grid infill, 20%. My printer can print the tensioner M5 screw, hope yours can too. Lubrication helps. Kitchen oil works fine. ...It is in the position i printed them, used support only where touching the bed.

I leave you the stl files and the gcode of these temp towers of mine already calibrated for PLA PETG ABS

A sleek, modern room lamp makes a striking impression when its base and shade are 3D printed using a vibrant orange transparent PETG material.

even with maintaining this page or BOM.\r\n\r\n####WHAT\r\n\r\n##### Custom-built CR10 S4 printer from sourced and engineered parts. Build volume 400x400x500. As much printable as it can be. \r\n\r\nI want to share my design choices and where I want...

... them in PLA as there is no heat involved so they won't warp. PETG or other advanced plastics work too. Printed and tested, they fit perfectly without any glue needed. ... If necessary, adjust their dimensions using your preferred slicer software.

This Is A Simple Coffee Mug That I Made In Tikercad. ...If You Do Not Use PETG, Then It Might Not Food-Safe, And Could Also Be Prone To Warping. I'm Entierly Sure That PETG Is Dishwasher Safe Too, So Make Sure You Use The Right Filament!

This profile features standard-sized holes (0.100" and 0.063") designed specifically for cutting with a CNC water jet. A variety of finishing processes are required, including: * Opening the holes to size * Tapping the necessary holes (heat pad) *...

... A separate model is provided for each size, so feel free to duplicate them within your slicer. If needed, you can easily adjust the clips' width or depth in any slicer before duplicating the modified model. Printing with PETG is also recommended.

The dual-zone heating system allows for faster cooling times and reduced warping, making it perfect for printing with sensitive materials like PLA and PETG. Additionally, the hotend's compact size and easy-to-use interface make it an ideal choice for...

If you print PLA or PETG this most likely wont be the case. To test the fitment I have attached separately the center section so that you don't have to print the entire wheel to check the fitment. As soon as you are happy with the fitment use the...

After many "try and cry" attempts: I succeeded in combining PETG and TPU and printing it with the MMU2S. I made a smartphone flip case for a Samsung J7 and a Xiaomi Mi A2. The outer layer is printed with PETG (turquoise), the case with TPU (semisoft,...

QTY 4 M5 x 35mm Hex Head Cap Bolts (for bottom brackets)...

I opted for PETG filament and it has performed admirably even after undergoing extensive use through multiple rolls of both PETG and PLA without any issues whatsoever. ...It's finally time to discard those makeshift paper clips that had been serving as...

Here is a simple adapter for two PETG or Bowden tubes that requires no infill or raft support. ...Designed specifically for tubes with an outer diameter of 6mm, this clip allows for easy connection and disconnection without the need for any additional...

... Suraky. ...To enhance printability, I narrowed both dimensions by 0.2mm, resulting in faster printing times and reduced material usage. When printed with PETG, these straps are remarkably comfortable to wear and can be easily molded using warm water.

... intended to test retraction and stringing/oozing. ... Intended for PETG at 240-190°C. ... Printer: Ender 5 Plus Layer height: 0.2mm Infill: 10% Speed: 25mm/s for walls, 15mm/s for top/bottom, 30mm/s infill speed Fan speed: 40% Bed temp: 75°C

I have added a cut-out for the microphone, which is located at the top of the frame. ...PETG can be a bit slippery, so my tip: print it on a rough PEI spring steel plate. ...This way I was able to create a fabric-like feel.

It is enough, if I can easily recognize which filament is meant.-----------------------------------------------------------------------------------------------You can find the samples for other brands and materials on my account.So far I uploaded...

A couple comments that when others tried it was too tight, so I took a pass at modifying and testing with PLA+ and then PETG. Some of the supports are really thin, but adjusted various components and got to a model that appears to work okay.Printed...

Design is currently being used effectively at a medical device manufacturing facility. Each buckles requires approximately 28 minutes in print time. Print instructionsPrint in PETG, as PLA may not handle the flex design well. Printed at a 0.3mm layer...

... the crimp and former parts together with an M3 screw. Place the former into PETG material, then heat it with a heat gun. If desired, heat the base as well and push it onto the flared section. ...Finally, use the crimp tool to form a tightening ring.

... it my own twist. This Bumper is designed to be printed in PLA/PETG or ABS. It has been slightly downsized and trimmed on top and bottom. The edges have been cut to ensure a perfect snap fit. ...Some pressure is required, but it will fit perfectly.