simplisafe 3 3d models
751360 3d models found related to simplisafe 3.prusaprinters
It took me only 3 iterations to get to this design, so it's a relatively straight forward design. I designed it for:</p><ol><li>Printing with PETG material to take advantage of the flex characteristics of the material.</li><li>It allows...
thingiverse
A Mount to fit the Simplisafe camera onto the X-gantry of the Ender Pro 3 for monitoring from above. Use to monitor your print progress, or the room it's in! The snap feature securely holds the mount to the aluminium extruded bar, and the slot is...
thingiverse
I like the new Simplisafe 3 home DIY alarm system and I got a camera to watch my front door. They don't have a wall mount for the camera, so I designed one that fits in a corner. It can be attached with 3M command strips or #6 screws. It pivots...
thingiverse
I have a Simplisafe 3 alarm system (which I really like!). One of the options is a nice key fob for arming and disarming the system. For me the buttons are just a bit too easy to push, I kept hitting them when I took key fob out of my pocket or...
thingiverse
Remix of wtrow"s Simplisafe Simplicam camera corner wall mount https://www.thingiverse.com/thing:5192178 Original Corner wall mount stl was giving me first layer issues so I fixed it. Also made a square version, a 10 degree right and 10 degree left...
thingiverse
Backer plate for older style SimpliSafe sensors (the circuit board side)
thingiverse
Remodel Simplisafe Cap redesign to prevent loss of cap for usb key chain.
thingiverse
I wanted to separate the parts so I didn't have one long build but instead 3 shorter ones. I also adjusted some of the dimensions a little. After printing I used super glue to hold the pieces together. My original was a little tight putting the base...
thingiverse
This is a mount for a Simplisafe indoor camera to go into a corner of a wall. ... It uses original hardware from mount that comes with camera
thingiverse
My SimpliSafe Video Doorbell Pro has mounting holes that are 77~78mm apart for the holes to attach your mounting bracket to my wedge. Some newer ones (I think it's the newer ones) have holes 66.6mm on center, and they wouldn't fit the original model...
thingiverse
... to support the tabs This is for the SimpliSafe keypad (circa Dec. ...2019) The keypad mount from SimpliSafe was very flimsy and you couldn't put a normal grabber screw in with the clearance. ...This is just a slightly thicker version of the OEM.
thingiverse
Simplisafe doorbell mount I made to extend the doorbell out the the edge of my door frame so it is parallel to the street instead of looking into the wall of my house. ... See photos...
prusaprinters
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online.</p> <p>This is a tight fit (on purpose) and needs trimming...
thingiverse
The 3D printed camera back replaces the stand that comes with the SimpliSafe camera. There are two different types of wall mounts: one has holes for screws, the other has no holes so you can use 3M Command strips to stick to a wall. There are...
thingiverse
My neighbor has a SimpliSafe indoor camera and wanted to mount it high up on the wall. I used the normal stand for measurements and created a wall mount. It slides into the slots on the back of the camera. The mount also has a slight angle to...
thingiverse
This is a cover for the newer Simplisafe remote key fob. The buttons were a bit too easy to hit when it was in my pocket so I created this to add some depth to the buttons, including the panic button on the end. If prints on end with no...
thingiverse
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online. This is a tight fit (on purpose) and needs trimming to...
thingiverse
Designed this mount to secure my fob next to my bed and nightstand as a simple way to arm/disarm my simplisafe along with keeping the panic button at the top for easy access in case of an emergency. ...I would suggest printing it vertically since its...
thingiverse
This printed cover helps to conceal a Simplisafe entry door sensor by printing a cover in a matching color. Adding the cover to the magnet sensor may make the magnet to large to pass the door, in which case there is a low profile sensor case that...
thingiverse
This is a drop-in adapter for the SimpliSafe SimpliCam, allowing you to mount your cameras on the wall, rather than on a shelf with the original stand. It has a built in wire pass through if you choose to run your wire up to the ceiling for better...
thingiverse
Without any kind of modifications, the SimpliSafe doorbell could be stolen by a knowledgeable thief within about 15 seconds. This case makes it much harder to steal, and makes the doorbell visually blend in with the house better. I recommend...
thingiverse
The new Simplisafe doorbell need an angled mount to work for my house so I made this. There are a few things that are not quite right but it does work and is also secure. The mount was designed to angle the camera to allow mounting on a wall...
thingiverse
Replacement door sensor magnet mount for SimpliSafe home security system.
thingiverse
3) Using a carpenter's level, attach swivel base plate to exterior wall using wood screws, lag screws, etc. 4) Use pin to secure swivel base plate to swivel plate, pin head on top. 5) Attach Simplisafe camera to magnetic base. 6) Adjust angle as...
thingiverse
This plate is for the SimpliSafe indoor cameras. I have only drawn the plate so far, but this can be adapted to any sort of mounting system. More revisions to come! ... Hopefully this helps the people that agree that the little stand it comes with is...
thingiverse
This is an angled stand that is for the SimpliSafe indoor camera to get a better angle from the top. It is pitched 14.8 degrees. ... The foot that comes with the camera slides under the slot for a tight fit
thingiverse
Simplisafe Indoor Camera Wall Mount Requires: 1x M5x20mm machine screw 2x M5 Nut To mount it to the wall I used the spare Command Strips supplied with the system. ... I had to use a drill to put the screw through the hole as the hole is exactly 20mm ...
thingiverse
So I just purchased a SimpliSafe Alarm System (they are amazing). I purchased a key fob to turn the system on, off or put in home mode. What I didn't think about is how I hate have things in my pockets with my keys. So I took the metal clip off a new...
thingiverse
Spacer for mounting the Simplisafe Doorbell Camera. The location of my previous doorbell was on the door frame, which would cause a blindspot due to the brick wall. This spacer brought it out flush with the wall/shutters. You'll need 4 sets of...