simplisafe clearance 3d models
24886 3d models found related to simplisafe clearance.thingiverse
... to support the tabs This is for the SimpliSafe keypad (circa Dec. ...2019) The keypad mount from SimpliSafe was very flimsy and you couldn't put a normal grabber screw in with the clearance. ...This is just a slightly thicker version of the OEM.
thingiverse
Remodel Simplisafe Cap redesign to prevent loss of cap for usb key chain.
thingiverse
Backer plate for older style SimpliSafe sensors (the circuit board side)
thingiverse
The new Simplisafe doorbell need an angled mount to work for my house so I made this. There are a few things that are not quite right but it does work and is also secure. The mount was designed to angle the camera to allow mounting on a wall...
thingiverse
This is a mount for a Simplisafe indoor camera to go into a corner of a wall. ... It uses original hardware from mount that comes with camera
thingiverse
Simplisafe doorbell mount I made to extend the doorbell out the the edge of my door frame so it is parallel to the street instead of looking into the wall of my house. ... See photos...
thingiverse
Remix of wtrow"s Simplisafe Simplicam camera corner wall mount https://www.thingiverse.com/thing:5192178 Original Corner wall mount stl was giving me first layer issues so I fixed it. Also made a square version, a 10 degree right and 10 degree left...
thingiverse
The 3D printed camera back replaces the stand that comes with the SimpliSafe camera. There are two different types of wall mounts: one has holes for screws, the other has no holes so you can use 3M Command strips to stick to a wall. There are...
thingiverse
My neighbor has a SimpliSafe indoor camera and wanted to mount it high up on the wall. I used the normal stand for measurements and created a wall mount. It slides into the slots on the back of the camera. The mount also has a slight angle to...
thingiverse
This is a cover for the newer Simplisafe remote key fob. The buttons were a bit too easy to hit when it was in my pocket so I created this to add some depth to the buttons, including the panic button on the end. If prints on end with no...
thingiverse
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online. This is a tight fit (on purpose) and needs trimming to...
thingiverse
This printed cover helps to conceal a Simplisafe entry door sensor by printing a cover in a matching color. Adding the cover to the magnet sensor may make the magnet to large to pass the door, in which case there is a low profile sensor case that...
thingiverse
Designed this mount to secure my fob next to my bed and nightstand as a simple way to arm/disarm my simplisafe along with keeping the panic button at the top for easy access in case of an emergency. ...I would suggest printing it vertically since its...
thingiverse
This is a remix I made of the wall mount for the Simplisafe base station. I wanted to separate the parts so I didn't have one long build but instead 3 shorter ones. I also adjusted some of the dimensions a little. After printing I used super glue to...
thingiverse
This is a drop-in adapter for the SimpliSafe SimpliCam, allowing you to mount your cameras on the wall, rather than on a shelf with the original stand. It has a built in wire pass through if you choose to run your wire up to the ceiling for better...
thingiverse
My SimpliSafe Video Doorbell Pro has mounting holes that are 77~78mm apart for the holes to attach your mounting bracket to my wedge. Some newer ones (I think it's the newer ones) have holes 66.6mm on center, and they wouldn't fit the original model...
thingiverse
Without any kind of modifications, the SimpliSafe doorbell could be stolen by a knowledgeable thief within about 15 seconds. This case makes it much harder to steal, and makes the doorbell visually blend in with the house better. I recommend...
prusaprinters
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online.</p> <p>This is a tight fit (on purpose) and needs trimming...
cults3d
Designed to allow for mounting the magnetic mount included with the camera while moving it away from the mounting surface for more clearance around the camera.
thingiverse
Replacement door sensor magnet mount for SimpliSafe home security system.
thingiverse
Simplisafe Indoor Camera Wall Mount Requires: 1x M5x20mm machine screw 2x M5 Nut To mount it to the wall I used the spare Command Strips supplied with the system. ... I had to use a drill to put the screw through the hole as the hole is exactly 20mm ...
thingiverse
This is an angled stand that is for the SimpliSafe indoor camera to get a better angle from the top. It is pitched 14.8 degrees. ... The foot that comes with the camera slides under the slot for a tight fit
thingiverse
This plate is for the SimpliSafe indoor cameras. I have only drawn the plate so far, but this can be adapted to any sort of mounting system. More revisions to come! ... Hopefully this helps the people that agree that the little stand it comes with is...
thingiverse
Install: 1) Attach Simplisafe magnetic base plate to swivel plate. 2) Snap and twist Simplisafe magnetic mount to magnetic base plate. 3) Using a carpenter's level, attach swivel base plate to exterior wall using wood screws, lag screws, etc. 4)...
thingiverse
Spacer for mounting the Simplisafe Doorbell Camera. The location of my previous doorbell was on the door frame, which would cause a blindspot due to the brick wall. This spacer brought it out flush with the wall/shutters. You'll need 4 sets of...
thingiverse
The magnetic mount that's included with the SimpliSafe Outdoor security camera is great for cameras facing away from the mounting surface but creates an issue when the camera needs to be more parallel to the wall. This mounting bracket uses the...
thingiverse
So I just purchased a SimpliSafe Alarm System (they are amazing). I purchased a key fob to turn the system on, off or put in home mode. What I didn't think about is how I hate have things in my pockets with my keys. So I took the metal clip off a new...
thingiverse
This should fit snugly into the same slot that the SimpliSafe original stand fits in. Assemble with two M4x20 screws and an M4 nut. Tighten and should move with some resistance. No need to loosen and re-tighten when positioning camera. The...
thingiverse
This is a replacement case for a V1 SimpliSafe Entry Sensor. I needed something that was a little less bulky to fit behind some new blinds I installed on my windows. This one is just a little wider than the original, but will lay much flatter...