simplisafe doorbell 3d models

Simplisafe doorbell mount I made to extend the doorbell out the the edge of my door frame so it is parallel to the street instead of looking into the wall of my house. ... See photos...

Without any kind of modifications, the SimpliSafe doorbell could be stolen by a knowledgeable thief within about 15 seconds. This case makes it much harder to steal, and makes the doorbell visually blend in with the house better. I recommend against...

My SimpliSafe Video Doorbell Pro has mounting holes that are 77~78mm apart for the holes to attach your mounting bracket to my wedge. Some newer ones (I think it's the newer ones) have holes 66.6mm on center, and they wouldn't fit the original model...

Spacer for mounting the Simplisafe Doorbell Camera. The location of my previous doorbell was on the door frame, which would cause a blindspot due to the brick wall. This spacer brought it out flush with the wall/shutters. You'll need 4 sets of...

The new Simplisafe doorbell need an angled mount to work for my house so I made this. There are a few things that are not quite right but it does work and is also secure. The mount was designed to angle the camera to allow mounting on a wall...

SimpliSafe Doorbell right / left angle offset adaptor.

Protection for DoorBell wifi Camera

Doorbell put in the kitchen

Replacement doorbell case and button. ...I reused the contacts and hardware from the old one.

A little background: I wanted to design an entire doorbell that would work using a small wireless button. I settled on the [Sonoff SNZB-01 Zigbee Switch](https://amzn.to/3Ng2isk) (affiliate link). I also wanted it to "feel" like a doorbell, so I...

This is a replacement doorbell.It has a separate plinth that can be printed in a different colour. The button can be printed in clear and illuminated if preferred. The switch action is provided by two tactile switches (like these...

This doorbell housing fits a 30mm Momentary Reset Short Metal Push Button such as the one I used from this AliExpress link. Print the model face down and then apply multiple coats of spray paint for weather resilience. Wire the button using some...

Spacer for Simplisafe Entry sensor

Remodel Simplisafe Cap redesign to prevent loss of cap for usb key chain.

Backer plate for older style SimpliSafe sensors (the circuit board side)

This is a mount for a Simplisafe indoor camera to go into a corner of a wall. ... It uses original hardware from mount that comes with camera

... to support the tabs This is for the SimpliSafe keypad (circa Dec. ...2019) The keypad mount from SimpliSafe was very flimsy and you couldn't put a normal grabber screw in with the clearance. ...This is just a slightly thicker version of the OEM.

Remix of wtrow"s Simplisafe Simplicam camera corner wall mount https://www.thingiverse.com/thing:5192178 Original Corner wall mount stl was giving me first layer issues so I fixed it. Also made a square version, a 10 degree right and 10 degree left...

The 3D printed camera back replaces the stand that comes with the SimpliSafe camera. There are two different types of wall mounts: one has holes for screws, the other has no holes so you can use 3M Command strips to stick to a wall. There are...

My neighbor has a SimpliSafe indoor camera and wanted to mount it high up on the wall. I used the normal stand for measurements and created a wall mount. It slides into the slots on the back of the camera. The mount also has a slight angle to...

This is a cover for the newer Simplisafe remote key fob. The buttons were a bit too easy to hit when it was in my pocket so I created this to add some depth to the buttons, including the panic button on the end. If prints on end with no...

Designed this mount to secure my fob next to my bed and nightstand as a simple way to arm/disarm my simplisafe along with keeping the panic button at the top for easy access in case of an emergency. ...I would suggest printing it vertically since its...

This printed cover helps to conceal a Simplisafe entry door sensor by printing a cover in a matching color. Adding the cover to the magnet sensor may make the magnet to large to pass the door, in which case there is a low profile sensor case that...

This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online. This is a tight fit (on purpose) and needs trimming to...

This is a drop-in adapter for the SimpliSafe SimpliCam, allowing you to mount your cameras on the wall, rather than on a shelf with the original stand. It has a built in wire pass through if you choose to run your wire up to the ceiling for better...

This is a remix I made of the wall mount for the Simplisafe base station. I wanted to separate the parts so I didn't have one long build but instead 3 shorter ones. I also adjusted some of the dimensions a little. After printing I used super glue to...

This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online.</p> <p>This is a tight fit (on purpose) and needs trimming...

Replacement door sensor magnet mount for SimpliSafe home security system.

This is an angled stand that is for the SimpliSafe indoor camera to get a better angle from the top. It is pitched 14.8 degrees. ... The foot that comes with the camera slides under the slot for a tight fit

This plate is for the SimpliSafe indoor cameras. I have only drawn the plate so far, but this can be adapted to any sort of mounting system. More revisions to come! ... Hopefully this helps the people that agree that the little stand it comes with is...