simplisafe fob 3d models
3300 3d models found related to simplisafe fob.thingiverse
Designed this mount to secure my fob next to my bed and nightstand as a simple way to arm/disarm my simplisafe along with keeping the panic button at the top for easy access in case of an emergency. ...I would suggest printing it vertically since its...
thingiverse
This is a cover for the newer Simplisafe remote key fob. The buttons were a bit too easy to hit when it was in my pocket so I created this to add some depth to the buttons, including the panic button on the end. If prints on end with no...
thingiverse
I purchased a key fob to turn the system on, off or put in home mode. What I didn't think about is how I hate have things in my pockets with my keys. So I took the metal clip off a new chamberlain garage door opener and used it to clip it to my visor...
prusaprinters
<p>image was printed in PA6-CF but just about anything will probably work. </p>
thingiverse
Added a hole on the end so you can get to the panic button
prusaprinters
I designed it for:Printing with PETG material to take advantage of the flex characteristics of the material.It allows one end of the case to flex “open” and let the key fob slide in and snap closed once in place to stay on the key fob securely....
thingiverse
For me the buttons are just a bit too easy to push, I kept hitting them when I took key fob out of my pocket or bag. So I designed this to slide over the key fob and add just enough thickness to protect the buttons a bit. They are still easy to...
thingiverse
Remodel Simplisafe Cap redesign to prevent loss of cap for usb key chain.
thingiverse
Backer plate for older style SimpliSafe sensors (the circuit board side)
thingiverse
This is a mount for a Simplisafe indoor camera to go into a corner of a wall. ... It uses original hardware from mount that comes with camera
thingiverse
... to support the tabs This is for the SimpliSafe keypad (circa Dec. ...2019) The keypad mount from SimpliSafe was very flimsy and you couldn't put a normal grabber screw in with the clearance. ...This is just a slightly thicker version of the OEM.
thingiverse
Simplisafe doorbell mount I made to extend the doorbell out the the edge of my door frame so it is parallel to the street instead of looking into the wall of my house. ... See photos...
thingiverse
The 3D printed camera back replaces the stand that comes with the SimpliSafe camera. There are two different types of wall mounts: one has holes for screws, the other has no holes so you can use 3M Command strips to stick to a wall. There are...
thingiverse
Remix of wtrow"s Simplisafe Simplicam camera corner wall mount https://www.thingiverse.com/thing:5192178 Original Corner wall mount stl was giving me first layer issues so I fixed it. Also made a square version, a 10 degree right and 10 degree left...
cults3d
This is a wall mount for the SimpliSafe Control Panel. This is a tight fit (on purpose) and needs trimming to open it up very slightly, and doesn't need a bottom hook for that reason. ...The supportive sides and the firm fit make it very secure.
thingiverse
My neighbor has a SimpliSafe indoor camera and wanted to mount it high up on the wall. I used the normal stand for measurements and created a wall mount. It slides into the slots on the back of the camera. The mount also has a slight angle to...
thingiverse
This printed cover helps to conceal a Simplisafe entry door sensor by printing a cover in a matching color. Adding the cover to the magnet sensor may make the magnet to large to pass the door, in which case there is a low profile sensor case that...
thingiverse
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online. This is a tight fit (on purpose) and needs trimming to...
thingiverse
This is a drop-in adapter for the SimpliSafe SimpliCam, allowing you to mount your cameras on the wall, rather than on a shelf with the original stand. It has a built in wire pass through if you choose to run your wire up to the ceiling for better...
thingiverse
This is a remix I made of the wall mount for the Simplisafe base station. I wanted to separate the parts so I didn't have one long build but instead 3 shorter ones. I also adjusted some of the dimensions a little. After printing I used super glue to...
thingiverse
My SimpliSafe Video Doorbell Pro has mounting holes that are 77~78mm apart for the holes to attach your mounting bracket to my wedge. Some newer ones (I think it's the newer ones) have holes 66.6mm on center, and they wouldn't fit the original model...
thingiverse
The new Simplisafe doorbell need an angled mount to work for my house so I made this. There are a few things that are not quite right but it does work and is also secure. The mount was designed to angle the camera to allow mounting on a wall...
thingiverse
Without any kind of modifications, the SimpliSafe doorbell could be stolen by a knowledgeable thief within about 15 seconds. This case makes it much harder to steal, and makes the doorbell visually blend in with the house better. I recommend...
prusaprinters
This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online.</p> <p>This is a tight fit (on purpose) and needs trimming...
thingiverse
Replacement door sensor magnet mount for SimpliSafe home security system.
thingiverse
Install: 1) Attach Simplisafe magnetic base plate to swivel plate. 2) Snap and twist Simplisafe magnetic mount to magnetic base plate. 3) Using a carpenter's level, attach swivel base plate to exterior wall using wood screws, lag screws, etc. 4)...
thingiverse
Simplisafe Indoor Camera Wall Mount Requires: 1x M5x20mm machine screw 2x M5 Nut To mount it to the wall I used the spare Command Strips supplied with the system. ... I had to use a drill to put the screw through the hole as the hole is exactly 20mm ...
thingiverse
This plate is for the SimpliSafe indoor cameras. I have only drawn the plate so far, but this can be adapted to any sort of mounting system. More revisions to come! ... Hopefully this helps the people that agree that the little stand it comes with is...
thingiverse
This is an angled stand that is for the SimpliSafe indoor camera to get a better angle from the top. It is pitched 14.8 degrees. ... The foot that comes with the camera slides under the slot for a tight fit