sims 4 to obj 3d models

Part models from chapter 4 of PROTEC used as examples to class modeling practice:► Simple bearing support - PROTEC_4-8_P01.ipt► Angular arm - PROTEC_4-12.ipt► Inclined and assymetric support - PROTEC_4-14.ipt► Support with 2 holes -...

... a Bigtreetech SKR Pro v1.1 into the control box of my Folgertech FT-5 and this was the simplest method I came up with. ... This design holds 4 M3 nuts captive to mount the SKR Pro to the adapter and has 4 M3 holes to match MKS Gen 1.4 mounting holes.

This clip is designed to hold the 4-pin connector from Modern Robotics Sensors or Encoder Wires to the voltage converter and the 4-pin JST cable using just a zip-tie.

This is a standard-issue Sim's icon that contains ample room for embedding a basic LED lighting system, complete with a designated compartment for a straightforward on/off toggle switch.

now in obj

1/4 Inch to 1 7/8 Inch Flexible Connection Clamp Fabricated Through Additive Manufacturing for High Temperature Applications

A Seat Post shim, from 27.4 to 30.9. ... The higher the infill, the stronger and safer!

Compact design 90-degree angle, 4-inch to 2.5-inch adapter for quiet operation in commercial environments.

1/48 Scale X-4 Ruhrstahl Air to Air Missile created in Tinkercab in 3 sections and one whole piece,

Upgrading the Folger Tech FT5 printer from the standard MKS V 1.4 firmware to the advanced SKR 1.3.

BSP Pipe Thread G-3/4" to Gardena Adapter. This model is best printed solid with PETG. ...No Supports required.

its an adapter for a 3.5 inch diameter intake tube to a 4 inch cone air filter

1/72 Scale X-4 Ruhrstahl Air to Air Missile created in Tinkercab in one single piece.

A wheel adapter measuring 100*4 is convertible to a 114.3*5 size, enhancing its compatibility and usage.

This adapter converts a garden hose attachment to fit a 3/4 inch Schedule 40 PVC pipe.

1/40 Scale X-4 Ruhrstahl Air to Air Missile created in Tinkercab in 3 sections and one whole piece,

Adapter from 1/4 inch screws to 3/8 inch screws commonly used in photography, especially in tripod heads.

1/48 Scale X-4 Ruhrstahl Air to Air Missile created in Tinkercab in 3 sections and one whole piece.

This adapter enables connection of a DG-10 air blow gun to typical 1/4 inch pneumatic couplings.

... to attach a camera, microphone, or lamp to a small and affordable lighting stand. To use this adapter, you will also need three M5 screws and nuts, as well as an adapter from 1/4 inch to 3/8 inch, plus a further reduction from 3/8 inch to 1/4 inch.

I made this to adapt my 1-1/4" shop vac hose to work with this dust separator: https://www.thingiverse.com/thing:4460331

This clip is inserted into a 1/2" PVC pipe and allows it to clip on to a 3/4" PVC pipe

This clip is inserted into a 1/2" PVC pipe and allows it to clip on to a 3/4" PVC pipe Category: DIY

Needed a way to conected the 4 inch Sch 40 PVC pipe to the 5 inch inlet on the dust collector.

This clip is inserted into a 1/2" PVC pipe and allows it to clip on to a 3/4" PVC pipe

This is an adapter to go from a 3/8-16 mic stand screw down to a 1/4-20 camera mount. ...   Very light duty item.

Raspberry Pi 4 case with HDMI to CSI-2 module. Designed to use with screws. I used screws typically found in gameboys. ... Perfect for Pi KVM project.

this is a 4inch to 5 inch adapter velocity stack so i can adapt a 5 inch K&N filter to my 4 inch intake pipe.

This adapter attaches Pololu Universal Aluminum Mounting Hub (4-40 holes, 1/4" shaft) to VEX 4" mecanum wheel without permanent modifications, compatible with other six-holed hubs but not tested. Uses front and back plates from .STL file plus 1-1/2",...

To accommodate a nano sim from my iPhone 5, I printed an adapter for my iPhone 4 using an Ultimaker. The fit is perfect and it works seamlessly for me. ...In case of issues, you can adjust the openscad file.