singer tiny serger ts380 plus parts 3d models
601373 3d models found related to singer tiny serger ts380 plus parts.thingiverse
I made this gear to replace the broken motor gear in my Singer TS-380 Tiny Serger.
thingiverse
... spools and a spool retainer for regular spools of thread. I designed these for a Huskylock 234D, but if you find that they fit any other models then please let me know and I will list those as well to make it easier for people to find these parts.
thingiverse
This is a serger spool adapter for a heavy duty singer 4411. It holds the serger spool vertically, but mounts on the horizontal spool holder as shown in the photos. I tried the "cone" type and had difficulty threading a bobbin with them because...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/aWXBeMhzjGS
thingiverse
Tiny bee made of 5 parts, still trying to get the parts to fit together properly
thingiverse
Just a tiny simple box with shallow, curved compartments, for easy storage of tiny electronic parts while working on a project.
thingiverse
Tiny bee made from 4 parts. ... Should be easy to assemble though haven't tested it yet.
prusaprinters
It's a tiny parts bin! Not much to it other than it easily holds your little bits while you work on your stuff. I decided I needed one while I was disassembling and reassembling my Logitech G920. I had a few too many tiny bits to just leave laying...
cults3d
The funnel shaped corner facilitate the pouring the parts into bag or box while the parts in the other compartment remain in the tray, this is handy when I needed to separate the small screws, nuts and shims which packed in same bag. The tray can be...
thingiverse
The funnel shaped corner facilitate the pouring the parts into bag or box while the parts in the other compartment remain in the tray, this is handy when I needed to separate the small screws, nuts and shims which packed in same bag. The tray can...
thingiverse
This box was designed for fitting small screws and other loose parts when disassembling electronics. It's thick base helps prevent tipping on your desk, and it was made to be easily sealed with blue painters tape. ...The tape also gives you a great spot...
thingiverse
These parts were created for my 'remix' of a French 1980s single board computer, the MicroKit09. The switches used have a grid of 7.5 by 5.0 mm pin layout and the pin extrudes 5.7 mm. The total height (board - pin-top) is 9.5mm. The pins are slightly...
thingiverse
- support me and buy you multirotor stuff @ Banggood: http://bit.do/rc-toys-hobbies and save 8% with Coupon Code: rchobbies8 Parts (Referal Links): Servo:...
prusaprinters
These parts were created for my 'remix' of a French 1980s single board computer, the MicroKit09. The switches used have a grid of 7.5 by 5.0 mm pin layout and the pin extrudes 5.7 mm. The total height (board - pin-top) is 9.5mm. The pins are slightly...
prusaprinters
These parts were created for my 'remix' of a French 1980s single board computer, the MicroKit09. The switches used have a grid of 7.5 by 5.0 mm pin layout and the pin extrudes 5.7 mm. The total height (board - pin-top) is 9.5mm. The pins are slightly...
thingiverse
One of my favorite singer ! try to make better ! ...so upload version 2 upload version 3
grabcad
This is my Singer sewing machine modell with mechanism and with the video of anlysis.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_name = Aladin line5 = line4 = line3 = line2 = line1 = Singer border_thickness = 3.6 whichextruder = monochrome glyph_coalesce = 25...
thingiverse
Zusatzverstrebung, Scharniere, Griff für die Sapphire Plus Einhausung passend für https://www.thingiverse.com/thing:5169490 Griff ist ein Remix von https://www.thingiverse.com/thing:2864118 (Plexiglas 2,5mm)
myminifactory
Druckeinstellungen: Layerhöhe: 0,15mmInfill: 30%Verwendete Hotenddüsengröße: 0,4mm -------------------------------------------------------------------- Some 3D printed parts needed to convert a Singer sewing machine from the 1960's to a BLDC motor,...
thingiverse
Requires FX806TC Camera or Just Print Rear Wire Part for all 4 arms. I designed this for a friend and had to build one of my own. ...15 degree camera tilt, Print Settings Rafts: No ...
thingiverse
I could not find some of my serger parts, so I made replacements :) Print upside down, no need for support.
thingiverse
... printed a couple of these so thy don't wobble on the pin located at the top of the sewing machine. This is for a spool adapter that fits on the bobbin winder for a singer sewing machine. ... The hole will need to be drilled out slightly to fit.
thingiverse
This allows your to vertically store spools from a serger sewing machine. ...Print multiples of the part and after placing the spools stack another of the printed parts on top, repeat ad-infinitum.
thingiverse
This a simple method of securing your frsky xm+ reciever in a toothpick/tiny whoop stack. 1 inch mounting pattern with m2 screws. Simple to print and fairly light. the xm+ is press fit through from the bottom. The mounting holes are made for m2...