skis for traxxas slash 2wd 3d models
2298803 3d models found related to skis for traxxas slash 2wd.thingiverse
hey, made some skis for my slash 2wd. ...skis are printed with pla and linkages with flexible filament https://youtu.be/sRequv5ERdY
cgtrader
For the left ski, have the rectangle on the ski be one the right. Then the left mount should align so the hex points to the right. If you have a m4 tap, use it in the 2 small holes at the bottom. If not, you don't really need it. I just screwed in...
thingiverse
Printed for a Traxxas Slash 2wd. (The 4x4 setup is different) This one doesn't use bushings or bearings, so it might wear out quickly. Seems to hold up pretty well though. Thanks, Enjoy! ...
thingiverse
I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.
thingiverse
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
cults3d
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
thingiverse
I designed this 3D printed upgrade that I call Mount for Anything for traxxas slash 2wd LCG m2. So I designed this 3D printed component for the purpose of laying a mount so one can put on a gyro or light system or anything else. This 3D printed...
thingiverse
This is a 73t 46p spur gear for Traxxas Slash 2WD. It should work with a 23 tooth pinion or larger. I never used it yet so please leave me a comment or like if this works. ...Thanks!
thingiverse
Nice big floaty skis for 1/10 Traxxas 2wd. The skids are about 2" (50mm) x 6" (150mm) not counting the kick ups. Risers are sized for Slash tire size, Rustler and Bandit conversions will have the front sitting a bit higher than stock which is...
thingiverse
These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ... Learn more about the process at www.RCDetails.ca!
cults3d
These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ...Learn more about the process at www.RCDetails.ca!
thingiverse
and it must be a traxxas 2wd slash LCG or HCG you may need double-sided tape depending upon what you did to your chassis but in my case there was no need for me to do that because it fits tightly and I would not worry about it falling off. ...So enjoy...
thingiverse
It has mounting holes to fit onto the Traxxas Slash 2WD stock chassis as well as the 2WD LCG chassis. It also has a mount where you can put the switch with skinny cut outs to tuck the wires underneath. There are tiny holes for screws to mount the...
thingiverse
This is a Traxxas Slash 2WD 1/10 model 64t (64 teeth) spur gear. I plan to use it with the 28 tooth pinion gear I just posted. It will not work with the 23 tooth pinion or lesser toothed pinion gears because it is smaller. This is not based on any...
thingiverse
This is a simple flat ESC Mount that fits in the stock ESC location on the stock Traxxas Slash 2WD Chassis and the LCG Chassis. It might fit other models that use the XL-5 ESC because that's what these holes line up with. The plate is 55mm x 55mm. I...
thingiverse
This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...
thingiverse
This is a 70 tooth Traxxas Slash 2wd spur gear, similar to part 4370. I have not yet tried with my 550 motor because the 76 tooth spur/ 23 tooth pinion combo provides a nice balance of acceleration and speed without melting my 550 brushed OOB...
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210...
thingiverse
This is a 46p 67t (67 teeth) spur gear I made for my Traxxas Slash 2WD 1/10. It's probably the fewest teeth on a spur gear that will work in combination with a 23 pinion gear. This baby zooms on my RC, but you really need to ease into the throttle...
thingiverse
I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. ... You will need: - Adjustable steering and camber links (VXL models should have this already) -...
thingiverse
This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...
thingiverse
... of the system, basically acting as a breakaway as to not damage the main part. You will need 2 flags (any type really), some M3 hardware (socket head screws and simple nuts), and it fits on a classic Traxxas brand wheelie bar. ...Hope you like it!
cults3d
Fixing battery was always annoying for me, so I prepared an "easy-click" solution. This holder you need just to (1) rotate down holder plate and then (2) rotate clip arm pressing holder plate to the battery, like photos shows. Important is to fix...
thingiverse
Fixing battery was always annoying for me, so I prepared an "easy-click" solution. This holder you need just to (1) rotate down holder plate and then (2) rotate clip arm pressing holder plate to the battery, like photos shows. Important is to fix...
thingiverse
Plow design remixed from "Snowplow for 3dsets Landy" This was a quick design I threw together right before a snow storm so I could take this out and try to play around with it in the snow. Just take off the bumper and use the 2 screws from the...
thingiverse
traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.
thingiverse
This is designed for a traxxas slash 2wd it allows you to mount the transmission backwards for better centre of gravity and cornering ability but you can also mount it stock. ...this was designed to be cut out of aluminium but can also be laser cut out...
thingiverse
I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...
thingiverse
This battery strap is meant for use on the Traxxas Slash. Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification...