sks picatinny rail mount 3d models

It was printed vertically, however I think it would be stronger printed with the top of the picatinny rail laying on the bed Fits Great, but keep in mind every sks is different. The tab with the key hole has been drawn long to allow for more...

This is an SKS picatinny rail, inspired by the great job done by Skyphex. This also uses the "parametric NATO/Picatinny Rail" by Bike Cyclist, over on Printables.com. YouTube videos describe how to remove the rear sight, and leaf spring...

An adapter that allows you to mount a scope on an SKS.

I highly recommend having a few washers laying around to stick under the rail as your leveling may be different from mine. Print at 100% infill on its side for maximum strength. I recommend PETG or higher filament. Do not use PLA as it won't last...

You will have to remove your bayonet and cleaning rod for this to work. Otherwise the install should be no issue. I will be working on a design which does not require the removal of the cleaning rod. ...Please make this and let me know what you think!

Another picatinny rail mount for flashlights. ...Made for ledlenser P6 Core and others with 27mm diameter.

Picatinny Flush Rail Mount Mounts flush on picatinny rail, beneath most scopes without risers. Rail Mount Flat Build Surface.stl has flat area, opposite the lock screws, for easier customization. ... Hardware Required:  - M3x6 (x2)  - M3 Nut (x2)

This is a mount for the Led Lender M7R flashlight. ... Diameter of the flashlight is 29,6 mm. You can use it with RIS: 1913 Picatinny Rail, NATO Accessory Rail (STANAG 4694) Weaver rail

Picatinny Rail / Tripod Mount, easy mounting option for mounting you gun or other Picatinny Rail mounted device to a tripod. Hardware needed can easily be purchased at local hardware stores. ... (1) 1/4-20 Flange nut (1) 10-24 Nut (1) 10-24 x...

A simple low-profile Mobius camera mount for a Picatinny rail. This mount also features an extended wall to keep the SD Card from ejecting during jolts like recoil. ... Designed for use on paintball markers or...

I have shown it mounted to the top of an AR-15 Reciever, it can also be mounted on the botom of pistol rails and any other type of picatinny accesory rails you can find! Instructions Print standing up with support attatch to rail, use two short...

Picatinny rail flashlight mount for Cree mini flashlight. Everything is friction set, no tools needed! It holds your weapon and light together very well, no rattling or movement. ...You can scale the ring for your needs.

Simple Picatinny Rail charm mount. Used between the lugs on your rail for a bit of a cleaner look. Print the Hole side, and the Locking side. I modeled the holes for M3 screws, but I had a bit of trouble and using a M2.5 seems to fit a bit...

This is a holder for a RunCam 2 that fits on a standard 20mm Picatinny Rail. It works in combination with the standard holder you get with the RunCam2 and the Tripod screw mount You need 2 X M4 bolts and nuts 1 x 1/4" hinged D Ring tripod slotted...

It attached to the picatinny rail system, it fits under my scope, which is great because that's all the rail I have. I'll upload some photos when I finish it. It is designed for a specific rechargeable flashlight that you can find on banggood by...

I designed this picatinny rail mount for my SiOnyx Aurora to mount on my airsoft rifles. Raises the camera by 15mm(0.6”). There is a notch at the rear of the mount to allow you to action the view finder clip and swap out batteries/sd cards. ... ...

I made this to mount a picatinny holster to a dash. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/02qEjXELAoo Print Settings Rafts: No ...

The three included models will each allow you mount a different small LED flashlight to a standard mounting rail. These were designed to be printed with Soft PLA filament so they can be squeezed on. Using a harder filament or a much softer filament...

Hello, I present two models of riser rail for airsoft and asg replicas. The taller one is 31.50 mm high and the other is 21.50 mm high. ...To connect them I used 4 M8 screws, 35 mm long, and 4 nuts.

I needed to make some custom mounts for accessories for my blasters, so i made this as a base to work from

... the original and mounted it on my HiPoint 9545 / 45ACP Carbine. ...When I fired the recoil caused the camera to progressively roll forward. This design should prevent that. Marked as WIP since I haven't been back out shooting with this mount yet.

... it on my HiPoint 9545 / 45ACP Carbine. ...When I fired the recoil caused the camera to progressively roll forward. This design should prevent that. Marked as WIP since I haven't been back out shooting with this mount yet. Category: Sport & Outdoors

I printed lazerusrm's 90 Degree GoPro Mount for Airsoft guns, however I found that the GoPro got in the way of the Sight, so I did some more research and found Whatsacc's solution, however this then meant that the GoPro was facing downwards. So I...

GoPro mount with picatinny rail for airsoft replica

Simple picatinny rail mount, to attach a remote pressure switch (eg. ...for a flashlight).

Simple picatinny rail mount, to attach a remote pressure switch (eg. ...for a flashlight).</p> Category: Sport & Outdoors

An UIT-to-Picatinny rail adapter. ...E.g. to mount a MantisX to a target shooting rifle with a standard UIT rail *** Ein UIT zu Picatinny Adapter. Z.B. ...zum Befestigen eines MantisX an ein Match-Gewehr mit UIT Schiene

Hi! ...This is a kit to attach a GoPro to a picatinny rail. Please note that the mount is modelled to the size of the included rail.

A mount for the ATN X-sight II remote that allows this remote to be mounted on a standard picatinny rail. ... Uses one m5x25mm screw and a nut.

Picatinny rail mount flashlight holder Diameter: 26mm (for 25-26mm diameter flashlight) 1x M3 30-40mm, and small washer 2x M3 20mm 3x M3 nuts