sky hero 3d models
26980 3d models found related to sky hero.thingiverse
JIB for Anakin Sky Hero from https://www.rcgroups.com/forums/showthread.php?2455099-Sky-Hero-Anakin-build-discussion/page94 measurements EDIT : Body.stl is a one part JIB
thingiverse
3 different arm versions for Sky-Hero Anakin to be able to use all the arm positions. I prefered to print these in PLA its more rigid. ...It is easier to break but its also cheap to print new ones.
cults3d
Simple design to add a discovery buzzer from hobbyking to a Sky-Hero Anakin. ...Use two cable ties to lock the buzzer in one of the carbon boom arms of the Anakin.
cults3d
3 different arm versions for Sky-Hero Anakin to be able to use all the arm positions. I prefered to print these in PLA its more rigid. ...It is easier to break but its also cheap to print new ones.
thingiverse
15mm inside diameter landing gear spacers for a cushioned landing, It will also help the copter from sliding around. ...It was made for a Sky Hero Spyder. ...Printed with ninjaflex
thingiverse
Simple design to add a discovery buzzer from hobbyking to a Sky-Hero Anakin. Use two cable ties to lock the buzzer in one of the carbon boom arms of the Anakin. ...Print Settings Printer: Felix 3.0 ...
thingiverse
SKY HERO Little Spyder Alternate - short legs
thingiverse
Quick release for the Sky-Hero Spy! ... Instructions print rotated 90 degrees and using 0.1 layer heights 40% infill using ABS
thingiverse
... a esc tray that can cover 2 ESCs DYS SN40A inside the Arm of Sky hero spyder multicopter. ...I developed this tray basically for easy esc mounting @ X8 layouts of Sky Hero Spyders. ...The cover clips are slightly different for the top and the bottom.
thingiverse
This is a set of frame spacer for the sky hero little spyder. Using these spacers will allow thicker Lipo Batteries to be carried in the battery slot. ...Spacers are available from 1 mm to 3mm thickness.
thingiverse
A mounting plate that fits the hole pattern on the sky hero spy, allows wires to be run underneath. Can be used on upper and lower plates. ... Instructions Mount with M3 bolts and lock nuts.
thingiverse
This is a simple Naza GPS Puck for the Sky Hero Spy arm. ... Instructions Print in ABS with a Layer Height of 0.2 Use double side tape to hold in position on the arm side and gps side
thingiverse
This is a esc tray that can cover 1 ESCs DYS SN40A inside the Arm of Sky hero spyder multicopter. ... The cover clips are slightly different for the top and the bottom.
thingiverse
Will also fit any other multicopter with 30mm tubular arms like Sky Hero spyder, trooper etc. Made primarily for this mast: http://www.banggood.com/Folding-GPS-Mount-Support-Holder-For-DJI-ZERO-QAV250-RC-Multicopters-p-983662.html?rmmds=search which...
thingiverse
Battery Bracket for Sky Hero Spy or RCTimer Trooper
cults3d
3D printed part i designed to fix two LED Boards and the Spektrum Satellite Rx to the Sky-Hero Anakin.
cults3d
This is a light bulb to mount on the motor-mount of a Spy, Spyder, Spyder 6. ...Suitable on a pancake version from Sky-Hero.
thingiverse
I wanted to put Cobra 2204 1960kV motors on a Sky Hero Little Spyder, but the original motor mount does not fit these small motors as these are not intended to be used on this quad copter. This is not advised by Sky Hero. Use at your own risk. ...
thingiverse
Both trays are available in 30mm (original sky hero size) but also in 31mm and 32mm which allows to enlarge the lips battery slot and carry thicker batteries. Original screws can be used. ...(self tightening M3 screws) I recommend printing with high...
thingiverse
This is a little thing very useful for Anakin Sky Hero, to maintain the XT60 connector. It's made with PLA Carbon. ...Print Settings Printer: Overlord Pro ...
thingiverse
this is a very simple peace to mount a Dragon Link 433Mhz dipole antenna on the Sky Hero Spy Y6 hexacopter you will need an extra M4 screw like the one used to lock the arms.
thingiverse
Simple part that allows to clip the Naza V2 Led in place and can be used to put in the Sky Hero Spy frame using a M3 Screw beetwen the frame. ... Instructions print rotated 90 degrees in ABS at 0.1 layer...
thingiverse
This is a simple cam mount for the sky hero spyder frames. The Mount can simply be glued/laminated into the canopy. It is suitable for Runcam Owl Plus. Probably some other that are having the same size as well. The mount is available in 3 different...
thingiverse
Suitable on a pancake version from Sky-Hero. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 ...
thingiverse
The best canopy for the OB1 hands down! ...Print Settings Printer Brand: LulzBot Printer: Mini ...
thingiverse
I designed a replacement for the existing orange plastic mount because it wouldn't fit my 28x28 boardcam, there is also a .skp for a blank mount so you can tweak it for your camera. A rubber band (same size as the ones for the canopy) should be...
thingiverse
Convert your ob1 to superlight setup Print Settings Printer Brand: LulzBot Printer: Mini ...
thingiverse
This is a very clean and functional RGB LED Holder which allows a clean installation of RGB LEDs at the arms of X4 little spyders. It fits to the underside of the original little spyder motor mounts. The power cables can be routed inside the arms so...
thingiverse
A printed isolator block which holds 2 M4 bus bolts for power distribution. Instructions You will need... 2 Hexagon Head M4 x 20mm bolts. 2 M4 half nuts 2 M4 lock nuts Slot the M4 bolts into the...