sky watcher 8 dobsonian telescope 3d models

Replacement cap for polar alignment scope on Sky Watcher Star Adventurer GTi and 2i. ... Print in Glow-in-the-Dark or white filament to better find it at a sark site.

... small (ebay obtainable) switch and your choice of LED, I've also made it large enough to use a 18650 cell in a holder for ease of charging. Fits the larger style Sky-watcher tripods (EQ6, AZ-EQ6) does not fit EQ5. ...(any others I haven't tried)

This cradle is designed for a Sky-Watcher EQ5 dual axis motor drive controller, featuring holes in the back for attaching it using cable ties (not included). Additionally, loops on top and sides can be used with elastic bands or string. If desired,...

The rear elevation adjustment bolt on the Sky-Watcher EQ6R-Pro mount has a spring loaded handle that can be difficult to use for fine adjustments while doing the polar-alignment (PA). It tends to slip and not grab all the time. While doing some...

This is a Stepper motor bracket for the Sky-Watcher 80ED DS Pro that has had the focuser upgraded to the OVL one. You will need 4x M3x10mm to attach the motor to the bracket and 4x M3x20mm with washers to attach the bracket to the focuser. You will...

I needed a mount for my Sky Watcher EQ6-R tripod so I could mount a Raspberry loaded with AstroBerry on it. I used the extra high version of the Malolo (<a...

This thing will let you mount your PoleMaster to your Sky Adventure with out removing the mount ring from the PoleMaster. Print ring side down with support. Other Parts: M4 X 12mm socket headed cap screw 4 x M3 x 4mm set screws M4 tap and...

The rear elevation adjustment bolt on the Sky-Watcher EQ6R-Pro mount has a spring loaded handle that can be difficult to use for fine adjustments while doing the polar-alignment (PA). It tends to slip and not grab all the time. While doing some...

... is pretty stout. Designed to clamp shut with 1/4" hardware and 5/8 washers. It holds with a tight slip fit. ... I'm not doing it, but the fit can be snugged up by sanding a little off the mating flanges, or a loop of soft tape on the tripod leg.

The Newton telescope boasts an impressive 8-inch diameter lens, measuring a substantial 203 millimeters in length. ... Check out this amazing project on WordPress at http://3dprinter.arkaine.net/.

The watcher is fully pre-supported and it is calibrated to stand 6cm tall. Be free to adjust to the size that suits you. ...Nothing will escape its visual vigilance but also by its synapses connected to the end of its tentacles even capture the pressure...

The Watcher guards the exit of Iriksha to the surface, ensuring no overly brave Drow make their way outwards, and those that do might think they are guided by the light given by Meloth’s body. Though in fact this light is a lure used to bring Prey...

After printing these 2 handles I sanded them down and coated them with epoxy to seal them from humidity. When assembling: First use (2) coarse wood screws to screw through the top holes in the handle into the mount. Then use a drill to drill...

Human: Orion Newton Focuser Adapter Design Adopting the Hybrid Sky Optic design for my Orion 200mm Telescope, I will be using a Nema11 stepper motor coupled with various GT2 timing belts (188, 16, and 36 teeth) to achieve precise movements. The...

Customized version of https://www.thingiverse.com/thing:3968935 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3968935

Customized version of https://www.thingiverse.com/thing:4581618 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4581618

ENJOY!

Flat Light Box for create Astrophoto Flat Frame on Sky-Watcher Newton 150/750mm telescope. ...FreeCAD source on https://github.com/romanhujer/Accessories-for-the-telescope/blob/master/FLB.FCStd Category: DIY

This is a Cable Tray design for a Celestron RASA 8 Telescope. ...To reduce star diffractions

Just an dobsonian mount. ... Here is all the wood parts: https://www.tinkercad.com/things/9CmM4V9sl0q I use this printed telescope: https://www.thingiverse.com/thing:4294635

The storage compartment is specifically designed to accommodate a Skywatcher 8-inch telescope, model Explorer 200/1000. The enclosure consists of two identical parts, each 3D-printed using PLA material, featuring a 25% infill density for added...

A 1.25-inch nosepiece webcam adapter, compatible with Sky-watcher 9x50 finderscope and possibly others of similar barrel size. The 'fins' enable elastic bands to securely hold it in place. The aperture is intentionally tight for a precise fit; minor...

Creating an Astrophoto Flat Frame for the Sky-Watcher Newton 150/750mm Telescope Requires a Customized Light Box Solution. The flat light box is designed to accommodate the specific needs of astrophoto flat frame creation, ensuring precise and...

This is a mount and retaining ring for an 8 inch diameter telescope mirror. I recommend printing this out of rigid material, like PETG+CF or PLA+CF, and make sure you measure and compensate for any material shrinkage, as the tolerances on this mount...

This is a custom mount and retaining ring designed specifically for an 8-inch diameter telescope mirror. To ensure accurate printing, I strongly recommend using rigid materials like PETG+CF or PLA+CF and carefully measuring for material shrinkage, as...

Sky-Watcher Heritage-130P Flextube with TS-Optics 2" Crayford focuser

DYI 3D printed GT2 Kit for autofocus Sky-Watcher Evoguide 50ED with ZWO EAF electronic focuser. You will also need a GT2 6mm width 260mm length timing belt and a 2GT timing pulley with 5mm bore, 6mm wide and 12 or more teeth for the ZWO EAF shaft. ...I...