skyfly gt3c 3d models
47 3d models found related to skyfly gt3c.thingiverse
... etc. :-) ----------------------------- Protože má vysílačka GT3C nevhodně předsunutý volant, který neumožňoval řídit model jednou rukou, tak jsem vyrobil nový design volantu. ... Umožňuje to pak například druhou rukou natáčet auto za jízdy apod...
thingiverse
This fits inside SkyFly RC Airplane and replace the inrunner brush electric motor.
pinshape
Requires no modification to the the transmitter outside of removing the factory wheel (held on by two screws) and bolting this one on in its place. If you like to shoot videos of your crawlers while driving it is a must to be able to drive with one...
cults3d
This is a camera mount to fit the Flysky GT3C radio transmitter. It lets you fit any camera with a 2 prong GoPro style mount. The main housing has 6 positions, 3 on top and 3 on the front, the camera mount can fit to and it can also be mounted...
cults3d
If you like to shoot videos of your crawlers while driving it is a must to be able to drive with one hand and without something like this that just isn't possible with the GT3C. If you have a fitment issue mating this wheel to the controller I...
cults3d
Unfortunately my thumb is too short to hit original steering wheel of Flysky GT3C so I've made a prolongation of original steering wheel. On the internet are many of this solution but mine lets You put Your thub anywhere on that prolongation part and...
thingiverse
This print fixes to the FlySky GT3C RC controller and allows you to steer a car or boat using your thumb whilst your index finger controls the throttle. There are even ridges on the steering arm to help with grip. I have also included an indent...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/497iewtDXpR
cults3d
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/497iewtDXpR
thingiverse
I have modified my GT3C transmiter and I am no longer using original power button. (Power switch wires are common problem for GT3C users). I have ordered steering wheel for transmiter from Yeah Racing. As expected not a single one could be modified...
prusaprinters
(Power switch wires are common problem for GT3C users). I have ordered steering wheel for transmiter from Yeah Racing. As expected not a single one could be modified to use on GT3C. So I started CAD and design quick adapter.</p> <p>-On hub for Yeah...
prusaprinters
<p>A case to hold the FLYSKY FS-i6X 10CH 2.4GHz RC Transmitter Controller (https://www.amazon.com/dp/B07Z9YNP7S), 8x AA batteries, and assorted accessories. ... The battery mounts are remixed from https://www.thingiverse.com/thing:9805 and the case...
thingiverse
The is a quick little mount to hold the antenna for a FlySky R6B Receiver in a vertical position on top of a ZMR250 (or H250 Chinese Frame).
thingiverse
Holder for the FlySky FS-GT3C Transmitter. ...You can screw it at a side wall or at the top wall to let your control hang down.
thingiverse
Clamp this onto your radio wheel so you can easily drive with one hand. ... I extended the thumb part for the Flysky for easy reach.
prusaprinters
<p>Vzhledem k velikosti modelu jsem tiskl tryskou 0,25 a výškou 0,07mm.</p><p>Materiál Ctech ASA</p>
cults3d
Clamp this onto your radio wheel so you can easily drive with one hand. ...I extended the thumb part for the Flysky for easy reach.
thingiverse
One aiming straight, one aiming angled 45 degree to the left, each for the camera above or below the base of the radio. ...
thingiverse
This is a custom steering wheel for the Flysky FS-GT3C transmitter. It mounts at the same 2 screws as stock, eliminates the power button (you need to move it to somewhere else), have shouders for holding the foam on both sides, and looks like a...
cults3d
This is a custom steering wheel for the Flysky FS-GT3C transmitter. It mounts at the same 2 screws as stock, eliminates the power button (you need to move it to somewhere else), have shouders for holding the foam on both sides, and looks like a...
cults3d
This is a version of my wheel for the Flysky FS-GT3C that have a knob for one hand driving. This one will print together with the tyre for avoiding slippage, but a tacky/rubbery filament is recomended for better grip. Edit 22/01/19: Extended the...
thingiverse
This is a version of my wheel for the Flysky FS-GT3C that have a knob for one hand driving. This one will print together with the tyre for avoiding slippage, but a tacky/rubbery filament is recomended for better grip. Edit 22/01/19: Extended the...
cults3d
I have verified it also fits well on the GT3C and the Radiolink RC4. This file could easily be scaled up or scaled down to fit other transmitters with different sized wheels. ... Designed to use a 8mm nut, and a bolt that is no larger than 4.5mm in...
thingiverse
Hated the foam this RC came with. I made a replacement out of TPU. Stretch the printed part with your hands before you install. ...15% infill and 2 shells...
thingiverse
Lost my power button so I tried whipping up a new one. This just pressure mounts to the power switch which is just a ~2mm post rectangular post. Worked fine and seems to hold on using AmazonBasics PLA. Using another brand it was loose so YMMV. ...
thingiverse
I remixed an awesome thumbsteer option for those of us with smaller hands. ...I have included the .stl of my addition which can be printed and adhered to the original and also the gcode for an ender 3 v2 where I combined the components in cura.
thingiverse
Did you bust your flysky trigger by braking too aggressively? Me too. ... Print this in TPU/TPE and glue it to the trigger.
thingiverse
print it with pla. You wil need two M3 screews. ...I use the original foam for the rim
thingiverse
This version is for very small fingers. ...You can use the original foam next to holder, but it falls down yet.