skywatcher 3d models
578 3d models found related to skywatcher.thingiverse
For Skywatcher Dobsons and for Eyepieces. ... Pour les dobsons Skywatcher et les occulaires, pour allonger le porte occulaires.
cults3d
For Skywatcher Dobsons and for Eyepieces. ... Pour les dobsons Skywatcher et les occulaires, pour allonger le porte occulaires.
thingiverse
Motorfocus for Skywatcher 200/800 Motor: Nema 14HS13 Arduino ASCOM Focuser Pro DIY
thingiverse
A simple hood to put on front of your Skywatcher 9x50 finderscope to avoid condensation. ... Easy to put and remove.
thingiverse
I designed a larger focuser knob for my Skywatcher 90/900 refractor. ...It is easier to focus, and less wobble.
thingiverse
This is an addition to the stock focuser of many Skywatcher dobsonians. ...The extra diameter allows for somewhat finer focus control.
thingiverse
Designed this Bathinov for a Skywatcher ED80. The cap is slightly larger than the tube. Add some electrical tape on thi inside. This makes it fit snugly without scratching the tube during repeated usage. ...
thingiverse
This is a designed Bahtinov Mask for the Skywatcher Evolux 62ED used in conjuction with the optically matched 0.9x Flattener and Reducer which decreases the f/l to 360, f5.8 The mask fits over the dew shield.
cults3d
A cover lid for Skywatcher evostar 72ED. I didnt like the original screw lid because of metal dust falling on lens so I made a lid instead! ... I hope you like it =)
thingiverse
For SkyWatcher 130 mm newton telescopes. It improves spikes and collimation. ... Collimation screws: M4 Support screws: M8 I recommend a central screw M5 at least 25 mm long You're welcome, @astro.db
thingiverse
This is a t-shirt holder for shooting flats for a Skywatcher 72ED (72mm). ...up to four t-shirts can be sandwiched to make perfect flats, especially when incorporated with an ASIAIR.
thingiverse
A cover lid for Skywatcher evostar 72ED. I didnt like the original screw lid because of metal dust falling on lens so I made a lid instead! ... I hope you like it =)
thingiverse
It is the little project that I was working on to make my Skywatcher 150750 EAF-compatible with my Astroberry. ...Inspired by Astroberry Focusor: https://github.com/rkaczorek/astroberry-diy
thingiverse
Rueda dentada para sustituir la original del enfocador del SkyWatcher ED80 Tamaño interno 43mm Aplicación de correa dentada GT2 para robotizar el enfoque del telescopio. ... Material ABS (235-250º)
cults3d
......It uses the same dimensions as the standard Skywatcher dustcap that comes with the telescope. The .stl is completely manifold and thus perfectly printable. It would honestly make my day if you could maybe rate or even upload a picture of the print.
thingiverse
... *almost* all slop/play in the connection. I am not sure if other Skywatcher mounts have the same size parts as I'm only new to astronomy but I suspect this will work with similar mounts like the HEQ5 and some other Skywatcher/Synta/Saxon mounts.
cults3d
... almost all slop/play in the connection. I am not sure if other Skywatcher mounts have the same size parts as I'm only new to astronomy but I suspect this will work with similar mounts like the HEQ5 and some other Skywatcher/Synta/Saxon mounts.
thingiverse
Mine is the eq-35i but I believe the lower mount is the same for the skywatcher eq5/6. This should also work for quiter2 Tiny PC MeLE Fanless Mini PC Quieter3Q...
thingiverse
A replacement knob for a 6mm D shaped shaft as found on my Skywatcher EQ5 telescope mount. V1 is a bit larger and a very tight fit so might not be able to get it off. ... V2 is a bit smaller and not quite as tight.
prusaprinters
Using the same dimensions as the standard Skywatcher dustcap.The .stl is completely manifold and thus perfectly printable.tested settings with PETG:layer height: 0.3mm2 perimeter shellsinfill: 20%no supports needed
thingiverse
Si tratta di un piedino specifico per il treppiede dello Skywatcher Mak 127 AZgoto da incastrare in quello esistente che ha un terminale a punta. Con questo, che ha la base circolare, sopra una pavimentazione liscia da più stabilità al telescopio.
thingiverse
... I printed it (probably nothing wrong with the design it could just be my printer scaling). ...So I used his brilliant idea and redesigned it for my skywatcher. ...If you find it is too loose on your scope then 'otherthings' original will work for you.
thingiverse
Focuser for Skywatcher Mak127 telescope. I chose a design that can be dismantled very easily. The housing is mounted on the dovetail while the big wheel is simply pushed on the focus wheel. The engine is a 28byj-48. ...The driver is an uln2003 The...
thingiverse
- SkyWatcher Heritage 150 modification: - motorizing the ALT/AZ axis for automatic pointing and star tracking, - motorising by using the 3d printed parts, bearings and 2GT belts used commonly in 3d printers, - adding the electronic for full...
thingiverse
......I used parameters that should work for a Skywatcher Evostar 120ED telescope. I printed the part for free at my local library and it worked just fine. ...It does fit a little tight, so if I were to make it again, I would make it 0.5mm larger diameter.