skyzone fpv 3d models
15607 3d models found related to skyzone fpv.thingiverse
I use it to power my Skyzone 02C FPV goggles. The XT60 connector from the goggle power cable connects easily to the EC3 in the side slot which provides strain relief. To assemble the two parts, I used two part epoxy. ...CA glue would also work...
thingiverse
remix of ps915`s Lipo Holder for Skyzone FPV Goggles http://www.thingiverse.com/thing:1010549 made to suit turnigy 1000mah batterys I made the holder sides a bit longer and added a battery alarm holder one in pic was printed with 0% infil just to...
thingiverse
If you use the goggles or hand them over to spectators, often you or they unintentionally push the buttons on top of the goggles. This little protector glued with some thin double sided tape prevents that. It is still possible to use the buttons...
grabcad
400mW - 5.8GHz - FPV Transmitter http://www.hobbyking.com/hobbyking/store/__27145__SkyZone_TS353_5_8G_400mW_FPV_Transmitter.html
thingiverse
I bought two Floureon Lipos for my Skyzone FPV Goggles. To easy change and hold the lipo on the googlestraps, i designed this lipo holder. Install: clip the lipo holder on the googles straps. You can leave it there. to swap lipo, just...
prusaprinters
I bought two Floureon Lipos for my Skyzone FPV Goggles. To easy change and hold the lipo on the googlestraps, i designed this lipo holder. Install: clip the lipo holder on the googles straps. You can leave it there. </li> <li><p>to swap lipo, just...
prusaprinters
<p>i just fixed the version of diepie and added some radii<br/> The model not in the right dimensions and also broken</p> <p>But thanks for the design! really usefull</p> <h3> Please upload a photo of your make.</h3> <p>This design is not for...
thingiverse
i just fixed the version of diepie and added some radii The model not in the right dimensions and also broken But thanks for the design! really usefull Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest...
thingiverse
plate material - flexible buckle - any hard plastic
thingiverse
This is just a 3D-printed shell that covers 2x18650 battery container, USB-C charging port for 2S batteries and fits right-sided goggle battery belt place. All electronic parts were ordered at Aliexpress and not expensive. The set consists of 4...
thingiverse
Power up your video goggles with lead acid power in no time! Yeah it's 6V! => No problem because your goggles has a 5V regulator installed! Everything is 5V! 12V is a lie! Maybe you don't like to have lithium batteries near your body too? After...
thingiverse
Here is a lens cover/protection for the SKYZONE 02C/02X FPV goggles. I've designed it to be printed flat with soft TPU so no supports are needed and the print can be fairly quick. The print will be flexible and in time it will hold the curve of the...
pinshape
FPV protection antenna. ...Cover securely fixed. Material high impact plastic PETG is Suitable for antennas Realac: https://goo.gl/tpmdR5 Suitable for antennas Skyzone: https://goo.gl/4TYPHe
thingiverse
FPV antenna protection. ...Lid is securely latched. Material high impact Petg plastichttps://vk.cc/9aGn9Q Suitable for antennas Realac: https://goo.gl/tpmdR5 Suitable for antennas Skyzone: https://goo.gl/4TYPHe
prusaprinters
So i designed a clip and printed it with my Mendel90 3D Printer. You can buy it here: http://bit.ly/skyzone\_clip Here you can the the article about that mod on my blog (german) On the blog you will find the STL for downloading....
thingiverse
http://blog.seidel-philipp.de/skyzone-v1-fpv-goggle-faceplate-hack-fatshark-faceplate-montieren/ Please upload a photo of your make. This design is not for commercial use or selling! Unterstützte meine Arbeit / Support my work: Thanks! ...=)...
thingiverse
This is an Air-Inlet for a better cooling of the VTX in the SkyZone Theer Flying Wing.
thingiverse
Adapter to use Fatshark and Skyzone lenses at the DJI FPV goggle
thingiverse
This is my vision, how must look FPV monitor holder for maximum usability.
thingiverse
... own camera and broadcasts it on a separate frequency. Skyzone 3D goggles can tune each display to its own frequency. On the quad in the photo I used a Skyzone 3D camera that was bundled with my goggles, but any pair of identical cameras should work.
thingiverse
I tried to order corrective Lenses for my DJI FPV Drone (https://www.amazon.de/gp/product/B07FS8BG2R/ref=as_li_tl?ie=UTF8&camp=1638&creative=6742&creativeASIN=B07FS8BG2R&linkCode=as2&tag=eisenfliege-21&linkId=134a0f9654416674168e2508c2819236) with...
thingiverse
This is a replacement 3d camera for the Skyzone 3d goggle set. This unit is 2/3 lighter, has wider spaced cameras for an enhanced 3d effect at greater distances and has the cameras and transmitters contained in the same unit. It is about gopro sized...
thingiverse
I have used this part for hold transmitter on my tricopter based on http://rcexplorer.se/projects/2011/09/the-tricopter-v2-5/ On second side is holder for MinimOSD.
thingiverse
I want to use a True-D V4 receiver on my Sky04X, so I decided to try to fit it. The board of True-D needs to be a little sanded to fit perfectly inside the bay, but it fits. This cover uses the original bolts and fits from True-D v4. ...
thingiverse
You can store 2-2,5 times more power than a Fatshark lipo. You need 3 Lithium 18650 cells. There are a lot of "bad" cells in the marked. They claim to hold over 4000mAh. Truth is THERE ARE NO 18650 CELLS THAT CAN STORE MORE THAN 4000mAh. Google for...
thingiverse
Not ready for printing yet! ... Protective case for the Skyzone FPV 3D goggles. 2 Parts Main camera holder And top cover This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/crakHgXdfKi