sleeves for exploding kittens 3d models

I basically just added 1mm more space to each side where the cards go, except for the Missions and Expeditions cards, where I only added 0.75mm to two sides in order to leave a very small wall. The grid overlay being used...

Remixed tray for Welcome to the Dungeon board game, designed with sleeved cards in mind and optimized for reduced material usage by approximately 25%. The STL file may exhibit minor imperfections due to stretching, but Cura+Ultimaker prints it...

Instructions Using the Following Options: Thickness is Set to 4 Rotation Amount is -4 Degrees Bottom Diameter is Exactly 50 Units Resolution is Fixed at 30 Points Per Unit Overlap Between Layers is 4 Units Pattern Rotation is Set to 6 Degrees Border...

Instructions Using the following options: width = 40 (replacing height) thinning = 3 (adjusting thickness) base_diameter = 62 (smaller than bottom_diameter for an interesting look) pattern_rotate = 9 (twist on pattern_spin) line_size = 3.5 (thinner...

So I redesigned it to accomodate for: => sleeved cards (remixed it for space usage, allow more cards and easier access) => allow the chibis : [AJade](https://www.thingiverse.com/thing:3417952) and [my...

I recently purchased the Sleeve Case for Raspberry Pi B+ from Walter on Thingiverse (http://www.thingiverse.com/thing:604915). My Raspberry Pi isn't always readily available, so I needed a solution to securely attach it to the case. To achieve this,...

This design is made for the card game Fight for Olympus. The cards are sleeved. Print the box. Print in this order : - print logo (centered on the plate) - pull off the external frame - change the filament - print the lid (centered and with the...

This is a slim protective sleeve designed specifically for the Yubikey 5 or Yubikey 5 NFC (and possibly other models as well). Its main goal is to colour code different keys, but it also offers some protection and, if you choose a bright color, might...

Box for cards 41x63 of Descent + Nerekhall, they fit perfectly sleeved. In the slots (from smallest to largest) I have ordered them like this: 1] Relic cards 2] Quest cards 3] Status cards 4] Level 2 market cards 5] Market charts level 1 6]...

Box for cards 56x87 of Descent + Nerekhall, fit perfectly sleeved. In the slots (from smallest to largest) I have ordered them like this: 1] Player help cards 2] Travel event cards from the base game 3] Nerekhall Event Cards 4] Level 1...

This travel box is for the card game Unearth with sleeved cards. Print the box. To print the lid, do in this order : 1- print the logo (centered on the plate) 2- pull off the external frame 3- change the filament 4- print the lid (centered and with...

It also accommodates the trophy cups I designed for this game: (https://www.thingiverse.com/thing:3599314). Two versions of the model are included: * Insert.stl is a single piece about 193 x 193 mm in size. ...* Insert Part 1.stl and Insert Part 2.stl...

Instructions Using the following settings: sleeve_height_percent is set to 95 spin speed is set to 23 revolutions per minute height of the spinner is fixed at 135 millimeters the color chosen for this customized fidget spinner is a solid black...

You can easily scale and alter this unique model using various parameters listed below: Size: Set at 18 Top Diameter: Customized to fit any requirement at 82 Resolution: At an optimal setting of 30 Spin Setting: Precisely tuned for accuracy at 57...

With these settings, you'll create an incredible piece that reflects your style: Overlap: Perfectly Planned at 5 units Sides: Shaped with precision and finesse, Six elegant sides will amaze Height: A majestic 135 units above the base Bottom...

My original had warped a bit when printing, so I had to sand it "square" for it to work - if I was printing another I might increase the sleeve by 5% or so to allow for irregularities in the original print. ... I was going to glue mine after I checked...

Select options such as size (16), bottom diameter (59.5), border (3), line thickness (3), sleeve thickness (1), top diameter (82), overlap (3), sleeve Z-offset (0), sleeve height percentage (58), color (black), spin (69), resolution (30), sides (15),...

I found these deck boxes already created (Remix added), but the unfortunate thing was that they simply did not fit my sleeved cards (I used FFG sleeves, which are a little thicker). So, I modified them all to my liking and am providing them here,...

http://www.thingiverse.com/apps/customizer/run?thing_id=99020 Instructions Using the following settings: Overlapping sections are set to 5 The color scheme is chosen as aqua Border width is specified at 4 units Bottom diameter measurement reads 59.5...

Cables stay neatly organized with these spacers. ...They keep single sleeve cables tidy, originating from the power source, providing efficient airflow and easy access to internal components.

Adapting the recipe tray to work seamlessly with the superior storage system from Fabmaszter is a breeze when using high-quality Mayday premium card sleeves.

The design engineer carefully crafted a precise three-dimensional representation of the protective sleeve surrounding the screw on Zelmer meat grinders.

Love the sleeve case, but wanted a fan. ...Used M3-0.5 x 16mm socket cap screws to attach a 40x40x10 fan.

Accommodates premium sleeved cards (I use Gamegenic sleeves, which are 100 microns) and vertical storage, with no lid lift.Print two of each of the small card trays (short and tall) and one of everything else. The Nightfall large tiles holder fits...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=99020 Instructions Using the following options: sleeve_height_percent is set at a level of 95, spin amount to 23 and color changed to aqua. border size remains steady at six units in length.

See the photo for dimensions. PartsSatellite Bracket Sleeve: this takes up all the slack so the pipe fits snug and won't wobble.Guy-Wire Plate Anchor: this allows you to anchor the guy-wire plate anywhere on the pipe. Guy-wires are recommended if...

Here is an insert to organize the cards for quick setups along with support for sleeved cards. I tried to minimize filament usage but maybe there is a better way, please remix and show us the way.I recommend printing the big card holder on its side...

Here is an insert to organize the cards for quick setups along with support for sleeved cards. I tried to minimize filament usage but maybe there is a better way, please remix and show us the way. I recommend printing the big card holder on its...

Instructions Using the following options: - bottom_diameter = 59.5 - sides = 6 - height = 135 - overlap = 6 - top_diameter = 82 - size = 17 - line_thickness = 4 - color = aqua blue - pattern_spin = clockwise 5 times - border = inner 3 mm width -...

A custom-designed cylinder with unique specifications has been created, showcasing an elevated sleeve height and precise diameter measurements. ... Key Features: * Sleeve rises at a significant 50% height percentage * Measured diameters carefully...