small clip on camera 3d models
1374687 3d models found related to small clip on camera.thingiverse
simple raspberry pi camera mount that clips on end of cross slide ( no bolts or screws needed)
thingiverse
The photo is of the clip-on designed specifically for one laptop--The one in the photo is not the one used in the .stl file I uploaded. The one I uploaded can work on any laptop, but needs adjusting. Print with PLA and add two 2M screws and a 60mm...
thingiverse
This bracket holds a mini-digital voltmeter and clips it on to my small block 18650 battery holder. ...The Tinkercad orginal is here: https://www.tinkercad.com/things/dyr2wYtfkIC-small-blocks-voltmeter-clip
thingiverse
This is a table clip-on camera which is very convenient to be use when need. ...Purchased parts needed:-: 50mm metal clip HEX screw M6x65mm (1 pc) HEX screw M6x10mm (1 pc) HEX screw M3x35mm (1 pc) HEX NUT M6 (2 pcs) HEX NUT M3 (1 pc)
thingiverse
... regular binder clip. ...Clip also keeps the USB cable in place helping the camera stay aligned. Created for use with the C270 camera mount, but has a generic top so can be used for any other attachments. ... https://www.thingiverse.com/thing:1066718
thingiverse
A very rough camera mount that just clips onto the side of your printer. The swing arm ensures it has a adjustable field of vision. Based on the works of : https://www.thingiverse.com/mark133/designs https://www.thingiverse.com/elproducts/designs...
prusaprinters
Clip also keeps the USB cable in place helping the camera stay aligned. Created for use with the C270 camera mount, but has a generic top so can be used for any other attachments. https://www.thingiverse.com/thing:1066718 Print instructionsCategory:...
thingiverse
Clip-on Raspberry Pi camera adjustable arm and camera case. The base is attached to a binder clip and can be attached to the bed and easy to re-position. ...Compatible with following Raspberry Pi base and camera case by barneyj:...
thingiverse
This is a clip-on camera mount I designed for my CR-10. It clips onto the 2040 aluminum extrusion running down either side of the printer. I works great with Octolapse. I designed it to work with these Camera Screw D-Rings but I'd expect it to work...
thingiverse
This camera mount is held to the heatbed with "small" sized clips. It can be quickly removed and installed as necessary. It should work only any 3mm thick heatbed with buildtak on it. Sample of video below using the mount to print another mount:) At...
thingiverse
Clip-on camera cover for the Oculus Quest 2, for when not in use, for lens protection, dust cover, and to guarantee privacy from hackers or Facebook. This version clips onto the groove and strap pivots so that it won't fall off when upside down or...
prusaprinters
This is a clip-on camera mount I designed for my CR-10. It clips onto the 2040 aluminum extrusion running down either side of the printer. ...I works great with Octolapse. I designed it to work with these Camera Screw D-Rings but I'd expect it to work...
thingiverse
This is an add-on to the 18650 small blocks (http://www.thingiverse.com/thing:1729730). It allows you to add "extension" connectors at the bottom end of the pack so you can parallel the packs, thus doubling the capacity. ...The flat "T" section is a...
prusaprinters
I couldn't find an easy and a fast way to attach the articulated camera mount by Sneaks onto 3030, so I made one myself.Takes a bit of force to clip on, but even if there's little wiggle room, it sits there sturdily enough and can be slid...
thingiverse
......The arm clips on to the back of of the x-axis, and the led strip screws on with the printed nut. If you have to resort to glue or double sided tape for the LED strip, so did I a couple of times before the final print :-P Non-printed parts: 1.
thingiverse
I remixed this one for my old Microsoft Nx 6000 for D6 or Monoprice Ultimate 3d printer. ... Support needs for those webcam which just need to clip on will works too. ... was rush to use it, support not even remove yet.
thingiverse
I needed a shelf to hold a wifi camera that didn't have a standard camera mount.
prusaprinters
A mounting surface that holds a standard tripod camera mount plate to a wooden moulding. ...The FreeCAD file is included with dimensions in a spreadsheet format, as well as easy to modify sketches.</p>
thingiverse
Edit it online https://www.tinkercad.com/things/4guXQtcoIkM This part is printed in 3 pieces, the slot on each end of the spine is made to the exact same size as the ribs, on purpose. It was made that way to give a snug fit, once you sand it down a...
thingiverse
I took the clip from thing:4636337, extended the arm so the camera will look down on the print bed and used the original arm and extender from thing:627395 Clipping it onto your 2020 frame may require some brute force but you could just soften the...
thingiverse
This depends on the type of band you use ZIPTIE_WIDTH and ZIPTIE_THICKNESS are for the ziptie holes and, for the ones I had lying around, are set to 4x2 CAMERA_HOLE_DIAMETER: The diameter for the camera to fit through. ...I found that this value worked...
thingiverse
Made a little clip for the "Snap-on Filament Filter/Oiler by idig3d July 27, 2016" it is made to double as holder + filament guide for the filter so it doesn't move around that much. ... Printing: Support = is not needed Raft = brim is needed because of...
prusaprinters
I was already using marcvivet's camera mount but since I started using this project that will turn your ribbon camera to a usb camera (that you can use on your computer, too) I decided to make my setup more compact.The inspiration came from this...
thingiverse
I updated the length of the part that clips on the Ender because it kept falling off mine. i wanted a PI camera mount that I could see under the nozzle while printing. I found this, but it was too short for my ender 3. So I lengthened the arm to fit...
thingiverse
This is a small hook for attaching to your wire sheliving near the wall to add a hook for belts or anything else. I printed them in white PLA + (inland / Micro center) with 3 perimeters and they are plenty strong. To install slide the hook (bottom)...
thingiverse
item is drawn standard measurements . ...it clips onto Primos Trigger Stick leg.
thingiverse
This is my design of a raspberry pi camera (compatible) support to picture the nozzle as close as possible in the CR-10 frame, There are a lot of compatible devices, for comfort those you see in the picture are: - [Raspberry PI compatible Camera with...
thingiverse
Support creation - IBAN number - CZ5120100000002201435026 The resulting quality and functionality It depends purely on your settings thanks to the following
thingiverse
Support creation - IBAN number - CZ5120100000002201435026 Print vertically The resulting quality and functionality It depends purely on your settings thanks to the following