small picture frame easel 3d models
425753 3d models found related to small picture frame easel.thingiverse
An "Easel" styled picture holder with hearts and small flowers on either side. Made for a relative who has a small engraving on some thin wood to hold it up. Smallish. ... Only measures 4-5" tall and ~3" wide.
thingiverse
How many of us have purchased those picture frames with the cardboard-cutout foot that eventually loses it's strength or somebody damages. Instead of throwing away the frame we lean it against something, hoping it will stay in place. I got tired...
thingiverse
This is a very small picture frame with a roughly ogee-shaped profile. It has little tabs to hold a small photo without glass. The size of the photo is similar to "wallet size". ... Unfortunately, a small amount of support material is required for the...
thingiverse
Small picture frame for photos the size of 3.2x2.6 cm (fits nicely with the option of contact sheet when printing images from windows) May use the included support or hung up by a single nail the newer frame has been reuploaded to fix mismatch...
thingiverse
The frame is 32 x 36 mm. ...The blue picture frame, in the pictur, is printed in high resolution "layer thickness 0.05 mm" ;-) it is printed on my ultimaker.
thingiverse
... sized to pass 1/4" rod through. Hardware required: (4) 1/4-20 all thread rod, length determined by your picture frame size. Add 4 inches for minimum length rod required. ... (4) 1/4-20 hex or wing nuts (4) 1/4" flat washers placed under the nuts
thingiverse
Here's a little clamp for helping with picture frame glue ups. YouTube: https://youtu.be/i-NYl57XfNw Suggest printing in PLA with the following settings: 0.25mm layer height 30% infill Overhang support Additional hardware items you will need...
thingiverse
A simple easel I made for some stained glass pieces my wife did for a commission. Approx 4" wide. ...
thingiverse
I designed this to hold up a plaque I printed for my father-in-law. ...I made it because I could not really find a nice picture holder that I liked. ...So here we are…
thingiverse
tired of the wind blowing your picture off the easel, no worries, size this to fit and fear no breeze.
thingiverse
The wind can blow but my picture stays put. ...Slide one on each of the legs of your easel and problem solved.
thingiverse
Small Picture Frame with hinged rear stay Visible picture area 73mm W x 95mm H (2.88" x 3.73") Rear stay hinge leg is print in place (hinge will work after printing) then stuck on to back plate. I used Bostik which makes a strong bond to the PLA The...
thingiverse
A small easel for displaying small pictures, CDs, artwork, books, etc. It has been tested with artwork that weighs a couple pounds but is not tall so the item being displayed must be short. It comes in two parts. ...Print both and slide them together...
thingiverse
Small coin easel I created to display some of my coins on a shelf. ...It's holding a 2 ounce silver coin in the picture but it works fine with 1 ounce and I'm sure other too.
thingiverse
I wanted some low profile picture easels that attach to the back of a picture frame. I saw some commercial ones out of metal, but nothing 3D printed so I designed these. Pretty simple print, I did it with .3mm height. ...The screw holes close a bit with...
thingiverse
Foot for tubular Easel / a-frame legs. ...Designed for flex printing for a tight fit, appears just as durable as the original rubber feet.
thingiverse
Designed to hold a 10mm deep small picture frame. Instructions Print on it's side so the side of the rear stand is facing the plate. That way there is no overhang/support to worry about. ...20% infill...
thingiverse
Needed to replace one of these knobs for my wife's easel. ...Accepts a glued in captured 1/4" nut in the back.
thingiverse
I looked all over the internet for a simple laser cut easel for displaying decorative plates and pictures, but I couldn't find any. So, I whipped this up quickly. I used 1/8" plywood to cut these out. The slot is large and sloppy so that you can...
thingiverse
This is just a small stand that you can use to hold either a book, a piece of artwork, or any other cool object that you want to show off, all without taking up too much space. ... The stand measures 125mm x 99.76mm x 93.48mm.
prusaprinters
It is quite a small design made for the "Picture Frame" contest. I wanted to try a little mechanism I designed and play with surface textures a bit. So the handle should look like leather and the mechanism allows the picture to be slipped into the...
prusaprinters
I quickly made these picture frames for my son's instant print thermal camera (INKPOT Instant Print Camera for Kids is the model). His camera prints pictures on the fairly common small thermal print paper that is about 56.5mm wide. The viewable area...