small tripod for dslr 3d models
2292667 3d models found related to small tripod for dslr.thingiverse
Fixed table tripod, can be folded into a small space. ... Nuts and bolts 2x self-locking nuts M4 2x nuts M5 2x bolts with a conical head M4 - 8 mm long 2x bolt M5 - 50 mm long 1x 1/4-20 UNC bolt for the camera
thingiverse
Decided to make a sturdy tripod that is small, lightweight and that can hold a DSLR/Mirrorless camera. The tripod requires ball head in order to be used properly with a camera as it legs uses hard stop to stay open. It does not support middle stops...
thingiverse
I have several filters for my DSLR that when I use them it is almost impossible to aim the camera. These filters include the Infrared Filter, the Solar Filter, etc. This small unit sits on the hotshoe and helps in aiming the camera. I made this...
thingiverse
DSLR rig for tripod mount. Ideal for macro photos. ... Required Hardware: 2 bolts, section 4mm, long 20mm 2 large washers, 4mm hole 2 butterfly nuts, 4mm hole 1 nut 1/4 inch https://youtu.be/8C_Z3eCwuWw
myminifactory
I wanted an small tripod that would be able to carry a DSLR in portrait and landscape mode. Many 3D printed tripods where either too small or not stable or didn't support portrait orientation. So I designed this one. Features - Portrait and...
prusaprinters
This is a mini tripod for cameras. WHY? I wanted an small tripod that would be able to carry a DSLR in portrait and landscape mode. Many 3D printed tripods where either too small or not stable or didn't support portrait orientation. So I designed...
youmagine
1" long 1/4-20 bolt through the ball swivel. ... 10/32 bolts for all of the leg mounts. Also for the middle Ball swivel mount to leg connector i used a square nut that fit and a bolt of appropriate length from the hardware store.
thingiverse
Small Tripod for Gopro Very easy to use and set your camera to film anywhere :)
myminifactory
Spare Tripod shoe which allows the 1/4'' thread to clamp DSLR to. Recess added so you can cut and add rubber for grip. ... You will need support underneath, best to set support infill to 10%
thingiverse
A small tripod that can support a DSLR or good size camcorder. Especially in soil / ground. The various holes in the tripod and mount are for rigging options. Can easily support 3-5 lbs. It was tested to 35 lbs was wobbly but held! Hardware is all...
cgtrader
Contains Subdivision Surface modifiers and Mean Crease edges data The materials are prepared for Cycles render All objects and materials are named Tripod legs are rigged with bone constraint
thingiverse
UPDATE: http://www.thingiverse.com/thing:827134 An easy-ish conversion for the manfrotto 3 way head to streamline taking of spherical panoramas. Made 2 so far but still work in progress. About 170 degrees vertical fov with samyang 8mm (corner to...
thingiverse
A small tripod for a Camera with 1/4“ screw, it’s designed to be light, small and stable. You use 3 legs, 3 pins, one base_plate and one Camera_plate or GoPro_plate Camera: it uses a 1/4“ screw witch can be printed ("screw1_4 for camera")or you can...
thingiverse
I needed a very small tripod to hold my Logitech c920 pointing at my printer. I've been propping it up using a failed print, but that's not the most stable platform. (See "Before.jpg") Other tripods are far more involved than I needed - I don't need...
thingiverse
i designed this pan tilt head in the course of my bachelor thesis for media-informatics at Vienna University of Technology The goal was to get highest angular precision for long-term timelapse photography. The device achieves a accuracy of 0.092° for...
thingiverse
Remix of GroPro DSLR tripod mount from: https://www.thingiverse.com/thing:81333 Previous design did not have proper sizing to hold #10-32 cap nut You will need these parts to assemble the mount (available at hardware store): 1 x 1/4-20 nut 1 x #10-32...
thingiverse
quick mount for your camera on your belt, when not in use. Designed around Arca-Swiss style plates. ...http://bit.ly/2fHEa68
thingiverse
A spare rubber surface for a small SLIK tripod. ...I printed it using filaflex 82a
thingiverse
This was specifically designed for a 3DR Solo - it allows you to mount any camera with a standard 1/4" tripod mount on the bottom. The hole is offset so a Sony a5100 has ideal positioning once mounted. It also works with a lot of GoPro accessories...
thingiverse
I needed a simple holder for my mobile phone and small tripod. It needed to be quick and easy to insert and remove the phone. Designed for desktop use only, does not hold your phone securely in other situations. ... Hole has 1/4 20 thread modelled in...
pinshape
Summary I needed a simple holder for my mobile phone and small tripod. It needed to be quick and easy to insert and remove the phone. Designed for desktop use only, does not hold your phone securely in other situations. ...Hole has 1/4 20 thread...
thingiverse
Needed a small holder for my cellphone, found modelmaker_PVG Mobile Phone Holder for small tripod https://www.thingiverse.com/thing:2821945 only my phone wouldn't fit with it's case on, so I stretched the holder and added a hole so I can recharge my...
thingiverse
My friend has a small spider tripod that he wanted to use for his Go Pro, so I made him this adapter for it. It seems to fit even better than the original. ...All you need is the Go Pro mount screw which comes with Go Pros and accessories.
thingiverse
... rise in two sections of the bottom. So I added a flat bottom to avoid using supports. This print fits this tripod http://www.camerachums.com/Targus-TG-5060TR-Tripod/p-427326?refid=Google I'm not sure how standard the tripod quick releases are.
thingiverse
I made this small dslr "tripod" (it actually has four legs) for my camera to stand on desk. The thread is exact dimensions for standard tripod mount. No support is needed or adviced for the print. Printed myself on Ender 3. Designed in Fusion 360. ... ...
thingiverse
Tripod for camera. There is a hole in the "plate" where a standard camera screw will fit. Gopro mount can also easily be glued to the plate. Size: Adjustable height: 4.3in-7in / 11cm- 17cm Diameter: 2.5in / 6cm Height when folded: 5.5in / 13cm You...
thingiverse
No need for screws. Print without support. ... Modifications: Changed lock angle Additional extended version
thingiverse
ADAPTATION for ARDUINO UNO NOT PRINTED YET