small wires 3d models
289580 3d models found related to small wires.thingiverse
They are suitable for small Dupont wires, often those received in kits or by 65pcs. They are approximately 11cm in total length. To assemble this stand, you don't need any tools or glue. It's really easy to assemble. The size is smaller and the...
thingiverse
I needed small wire management in my 3D printer enclosure (https://www.thingiverse.com/thing:3319066) to add some lights. I would be using wires that are 1mm and 1.5mm in diameter. I could not find a design that would work for me, so I designed my...
prusaprinters
I needed small wire management in my 3D printer enclosure (https://www.thingiverse.com/thing:3319066) to add some lights. I would be using wires that are 1mm and 1.5mm in diameter. I could not find a design that would work for me, so I designed my...
thingiverse
Me puse en campaña de armar esta base para soldar cables pequeños en corta distancia. De todas las herramientas de este tipo que hay en el mercado me parecen grandes y siempre me resultaron complicadas. Esta base tiene 5 x 5 cm y esta diseñada...
thingiverse
Small wire clip that can be screwed to whatever you need to organize wires within. ...The entire footprint is 10mm x 20mm.
thingiverse
If your like me and have a bunch of spools of small gauge wire and they are taking up a lot of drawer space..... Then I have something that may be of use to you. As you can see by the picture it will hold a few spools. ... I included the Fusion...
prusaprinters
This is a small wire spool printed in two halves to avoid supports. The two halves are threaded and there is a small hole for inserting the wire to make spooling easier. The outside rim has small slots for holding the other end of the...
prusaprinters
A small, 4cm long wire manager for cell phone cables and such. ...If you need a bigger one, just scale up the STL in your slicer software. </p>
thingiverse
... is 12.5mm. The inner part of the spool (in between the two sides) is 8mm wide and the two sides extend 2.5mm out and in from the inner part of the spool. It also has a small 2mm x 1mm rectangular hole in the spool for the wires going in and out.
thingiverse
This is a small spool that holds 1mm thick wires that I use for soldering. The diameter of the spool is 45mm. Just print out the two parts and put them together. ...You can use some glue to secure the part's but it isn't necessary and it should be...
thingiverse
A friend needed some simple, small, cheap spools that fitted in with the others he had for wire wrap wire. Lots of it. Internal/usable dimensions: 30mm core. 20mm depth, 23mm width. Two holes on each side for start/end. The larger one has a final...
thingiverse
30x50x12mm box with rounded edges, 4mm walls and 6mm entry/exit wire holes
thingiverse
The example size (45mm diameter 22mm high) barely fits 5m of AWG24 wire (silicone stranded tinned and so on) as pictured. ...This was made to just get me rid of the unwieldy dangle of wire.
thingiverse
Another bad model created while learning OpenSCAD. ... Holds 6 wire spools and **uses way too much material**...
thingiverse
#Files: I included the .stl files for the different spacing I encountered on my shelves: * 19.3mm gap, separating two 3mm\* wires * 27mm gap, separating two 3mm\* wires * 32.5mm gap, separating a 3mm\* wire and a 5mm\* wire (edge of the shelf) \*...
thingiverse
Quick remix of hlyman's jig. ...Made the hole slightly bigger and removed the front brace in order to get the iron onto the wire at different angles.
thingiverse
Quick and simple design i made to hold 3 spools of wire and mount on the wall. ...i printed at .2mm layer height, except for the threads which i use simplify3d to print at .25mm.
thingiverse
... things that shut us down, and this is one of those. ... if the wires on your x stop keep moving, they will break eventually so i made this little improvement (pun intended) i just bolted it on to the lead screw nut retainer. ... Hope you like it
thingiverse
I made this little clamp to hold very small wires in order to solder them parts required: x1 plateau_pince_cable.STL x2 3mm rod, lenght 8mm. I used metal rod but plastic rod or cut M3 screw should do just fine x1~2 rubber bands. I used horses black...
prusaprinters
The cable clips supplied with the original Lack table enclosure project (https://www.thingiverse.com/thing:2864118) are fine for larger cables or ribbon, but rather oversized for small wires like power for LED lighting. This is a small version of...
thingiverse
Modified the solder dispenser by Goldmond to hold 5 reels of small gauge wire for electronics projects. Spindle is thinner so it will fit through my reels. I'm new to modeling, so haven't figured out how to change the mesh on the base to...
thingiverse
I found a super good collections of cable clips at https://www.youmagine.com/designs/a-bunch-of-2020-misumi-cable-clips but I just needed 1 special clip to hold in the 2 wires for my LEDs. To make sure it is clear: This is a remix from a model...
thingiverse
I needed to bend some coathangers into a specific radius. This little tool made short work of them. Instructions Laser cut the parts out of 6mm material. 1x base 2x main 2x hinge 2x bolt trap 1x nut...
thingiverse
basic wirenut. yes, their cheap to buy, also I never seem to have them on hand! So print it! Best printed nose down. ...These were at 30% infill.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6hcrvON9rYv
thingiverse
This is a remix. I wanted to print original file in vertical without supports and I didn't need it to be that long, so I left only one clip there. ... I used it for LAN cable scaled to 120%