snap on models

You might want to remove the liner or even the double sided tape (with some IPA) to make them fit.remove the the strip and cut it to the right length.solder the wires to the corresponding copper patches of the strip.slide the LEDs back into the LED...

I've also incorporated a snap-on attachment for a dust or smoke-shoe, complete with the shoe itself. The bracket easily snaps into place between the upper and lower sections of the Makita holder, making it simple to install and adjust left or right...

A holder which takes a Nintendo switch (no joy cons attached) and attaches it to an 8-BitDo SN30 Pro+ Controller to create a DS-style grip. ... I replaced the controller mount into a snap on from https://www.thingiverse.com/thing:4639291

I'm modifying a snap-on heat sink cover for the Prusa i3MK3s. The original print was great, but it required me to take off the cover to access the screw holding the hot end fan duct in place. I always remove the fan duct for quicker nozzle swaps.

I needed a sturdy snap-on clip to secure the oil pan gasket in my Jeep, so I swiftly whipped up a makeshift solution instead of ordering one online. ...The design may be rough around the edges, but it gets the job done and I'm sharing it here for others...

... i made a publish version for you guys. It has some vents on the top and side. But don't worry i made it very easy to print without supports. The cap is snap-on design and you can easily remove it without damaging it while you want to use the GPIO.

This design borrows the "clip" and dovetail from this filament guide: https://www.thingiverse.com/thing:2917932 It also borrows the roller, axle, and tool-free, disassembly-free snap-on style of this lower guide (I'm still using this one for my...

I printed the Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 by sneaks and really loved it, but I wanted to attach it to 2020 bars for a stationary view without any t-nuts on hand, then I found the snap-on clip from Flexi-Arm Camera...

Here is the Ender 3 Pro Remix of the Snap On Filament Guide with a threaded hole for fitting PTFE tubing. This guide utilizes a fitting designed specifically for using PTFE tubing, similar to the one found on Thingiverse at...

Remixed Minimalistic Snap-on Screwless Raspi Case for Raspberry Pi Zero extrusion mount Mod the pin header position and add simple bolt holes, 2040 or 2020 both could work for bolt mount. with M3 bolt. I use it for Voxelab Aquila stock display...

I printed the Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 by sneaks and loved it but wanted to mount it to the 2020 bars for a stationary view but didn't have any t-nuts, I then found the snap on clip from Flexi-Arm Camera Mount by...

I printed the Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 by sneaks and loved it but wanted to mount it to the 2020 bars for a stationary view but didn't have any t-nuts, I then found the snap on clip from Flexi-Arm Camera Mount by...

It's based on my original Snap-on Prusa frame clip base, which can be found here: https://www.thingiverse.com/thing:2840786. The design features space for three LED strips in the front and one in the back to minimize hard shadows. Created and...

The different STL files: AL-MC_Grid_60degree – this is the snap-on grid featuring a 60-degree angle AL-MC_Grid_90degree – this is the snap-on grid featuring a 90-degree angle AL-MC_Case_Grids+MCs – this is the protective case that can fit two MCs...

Printed at a layer height of 0.1mm with 100% infill on the side with supports intentionally even though the part would print well on the back side because this way the parts are much stronger in areas that need it: the hooks where it snaps onto the...

Printer Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.1 Infill: 100% Notes: I printed on the side with supports to maximize strength at crucial sections: where the part hooks onto the feeder and bends...

Found this inexpensive DC/DC covnerter to power my Raspberry Pi that runs OctoPi , and made a snap fit set of clips and cover to mount it to the 4040 profile on the Ender 3 Pro. Pending thermal imaging after installing but in a slightly cool room...

Thus, I created a separate cover that can easily be snapped on or off while servicing the TOM. The cover's firm clamping prevents loosening, making it an improvement over the original. To print, use ABS filament at 0.1mm resolution with dense infill....

This snap-on endstop holder is quite efficient, which is why I wanted to share my experience. The design allows it to be attached to 8 mm X rods with a standard 45 mm centre-to-centre spacing. You can mount your limit switch in various positions for...

I created a small snap-in place holder that lets you access the port through a cooling vent on the right front. This way, you can use a standard microSD card in your SD adapter to flash screen firmware without opening up the case. ...You can buy an...

The Version 6 Slim iPhone 5 and 5S Snap-On Case (tested) is available at http://www.thingiverse.com/thing:30973; however, I made improvements by removing the Apple logo hole and slightly enlarging the power button hole. I have not printed it out yet...

... light sanding, no solution could be found. A revised model is currently being worked on and will be printed in black ABS as soon as possible to achieve a snugger fit for better aesthetics.\r\n\r\nOnce completed, I will update the design accordingly.

... One of its standout features is its snap-on functionality, allowing you to attach and detach it with ease whenever needed. When snapped into place, it sits flush against the mounting bracket, ensuring a smooth and uninterrupted printing process.

This is a little dial indicator holder, designed to snap an indicator, with an 8 mm stem mount, on the x axis of any 3d printer with a 2020 aluminum v-slot extrusion and a 12 mm linear rail. You can quickly snap the holder, along with the indicator,...

... and the sheet has there a 36mm opening. There are 6 slightly oversized snap-on extensions that also need a little squeeze when mounted. I didn't publish - and clean up ;-) - the OpenSCAD code as the STLs can easily be scaled. ...

I made this little snap in place holder that allows you to access the port through a cooling vent on the right-front. Allows you to use a common microSD to SD card adapter so you can flash screen firmware without opening case. You can buy an adapter...

Trailer part in PLA surprisingly rigid even with the openings.more beefygrips firmlyeasy to use for the kidsmuch freedom when connectedPrint instructions:When printed right, the part for the tractor stays in place without glue (flat surface pionts...

I'm grateful to the original creators who made their designs available for me to build upon - specifically, the Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 from Thingiverse (https://www.thingiverse.com/thing:3114849) and the Snap-on...

This a small but effective part that just snaps on to the stock spool holder. I've printed it with 0.2 mm layer height and %20 infill. (I've used PETG just because the only black filament I have right now is PETG :). ...Any other material would be...

......This easy-to-attach bracket simply snaps on to my SainSmart RAMPS board. The design features a fan hole spacing of 32, bracket thickness of 3.0, bracket length of 10, pcb width of 60, fan size of 40, bracket height of 35, and screw diameter of 3.25.