snap on razor handle 3d models
1254531 3d models found related to snap on razor handle.
thingiverse
An evolution of emmett's razor blade handle. Excellent for removing prints from the build platform. -tweaked the fit to work with the single-edged razor blades I'm most familiar with (Stanley #9?). Key to a forgiving fit was the full cutaway under...
thingiverse
Made for wire loop large buckets with a cheap handle that breaks off with normal use. The gap is about 1mm wide but i tried it on a 2mm wire and a 3/16" wire and both worked. ...It is 76 mm long which is about the same as most bucket handles.
thingiverse
A simple holder for EZ-Snap Razor Blade Handle made by AdanA
thingiverse
remix of https://www.thingiverse.com/thing:3184481 inspired by https://www.thingiverse.com/thing:930831 a bathroom hanger for one of those bath trays that has: - rod width: 2.5mm - distance between rods: 23mm it just snaps in and holds your razors :)
thingiverse
Snap-On screwdriver handle modeled by manually measuring one. This isn't exactly functional as-is, since there is no provision for attaching anything to the handle. This is uploaded so that others might remix it into something useful. Maybe add a...
thingiverse
... lunches to work in, but wanted a handle. ...This is a pretty sad attempt at it. I think I prefer the IN-THE-SIDE handles, but this does work and uses minimal material. ...I kinda expected it to rip out, but it's been holding up so I'm publishing it.
thingiverse
This is a Remix with my printer name on it, i also added a hole to suspend it with a screw or nail on your bench Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: .2 or .1 Infill: 50
thingiverse
This is a remix of "Voxelab Aquila Snap-on Bed Handle" that fits the ENDER 3v2. I used 4 walls and 40% infill for a sturdy handling. It has a really tight fit, be careful when assembling! ... Make sure your "Hole Horizontal Expansion" in your slicer...
thingiverse
It is a snap on handle extension that can freely rotate, making it much more ergonomic to handle and spin. Plus you can customize it to be whatever form factor or color you need! I added a drop of grease to the inside of mine, which helps it spin...
thingiverse
Being a Snap On tool, it has a lifetime warranty, but when I contacted Snap On I discovered it was obsolete and handles were no longer available. They replaced it with their latest model, but it is much longer and frankly not as functional so, when I...
thingiverse
Voxelab Aquila Snap-on Bed Handle Preface To me, a curious omission from many 3D printers is the lack of a handle to help manually manipulate what is, during normal operation, a metal plate heated to 60C/140F degrees or greater (codified by ASTM...
prusaprinters
<p>This is a remix to https://www.thingiverse.com/thing:2177302.</p>
thingiverse
No more hairy back! ... Need: - 2 stainless bolts 19mm (3/4") long, holes are 6.35mm (1/4") diameter - 2 stainless nuts to go with such bolts - zipties (I used two smaller ones) - razor (I am using disposable)
cults3d
No more hairy back! ... Need: - 2 stainless bolts 19mm (3/4") long, holes are 6.35mm (1/4") diameter - 2 stainless nuts to go with such bolts - zipties (I used two smaller ones) - razor (I am using disposable)
thingiverse
This is a simple, snap-in razor hanger that mates with a Gillette Fusion razor. It may work with other razors but I have only tested it with the Gillette Fusion. ... I plan to wall mount this using a 3M command strip.
thingiverse
A replacement tap / faucet handle for the water hose nozzles that Snap-On used to sell that constantly break. ... This one lasts a lot longer because it doesn't have the weak rubber part.
myminifactory
This coat rack is designed to mount onto the handle of a Snap-On Classic or Heritage series toolbox. I have put the original design sketch with the toolbox dimensions in the images if you want to confirm that it will fit your box before printing.
thingiverse
My design comes up with a "snap-on solution" that gets mounted on the left front wheel of the Y-axis carrier. It will need some force since it sits really tight on the shaft. The base idea contains the aspects of - easy to print - installation...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47842 Instructions Using the following options: Tool_Height = 10 Font = write/Letters.dxf Tool_Length = 8 Nut_Size = 12.7 message = Snap-On
thingiverse
I really like AdanA's EZ-Snap Razor Blade Handle, but since I have pets in the house, I realized it wasn't a good idea to leave them just lying around. I came up with this cover after spending a few hours fiddling around in SolidWorks. It snaps onto...
thingiverse
... I created this as I use single-edge razor blades a lot and figured it would be safer to keep them in a case than to leave them out on their own. ... Note: I have yet to print this but the snap-feature may need modification to function properly.
thingiverse
A razor handle based on the classic handles of the Schick Type E/G razors from 1935-1955 Either to be used as a replacement for broken vintage handles or as a base for modern 3D printed razors.
myminifactory
Lightsaber double edge razor handle for shaving. Add an m5 .8 nut to make it screw on to most 3 piece razor heads. Prints without support. ...May need to ream out the holes for the buttons.