snapmaker 2 3d models

Alle 3 Werkzeugköpfe inklusive dem passenden Snapmaker- Werkzeug Griffbereit am Gehäuse. Die Innenseiten sollten mit max 0.5mm starkem Filz beklebt werden, dann rappelt auch nichts. ... Mein allererstes Projekt, ich hoffe ihr könnt das brauchen.

... to hold the 3D printer module with the 5015 fan mod. The rack also has slots for cnc router bits, the included snapmaker tools and clamps. The holder is designed to fit on the A250 bed. ...Depending on settings, print time is about 40 hours.

https://forum.snapmaker.com/t/a250-mod-with-linear-rail/28513 The Step file is just the complete mock up of the snapmaker A250. Note not exactly to the mm done. just a sketch for myself to test some ideas. but if someone like it. please feel free...

If you have the Snapmaker A250/A350 and the matching enclosure... well .. then you know that the filament is catching on the left column as the extruder is moving from the home position down. This nifty little mod makes sure the filament is guided...

This is a fix for the Snapmaker Dual Extruder Module. The clip that hold the gear assembly into place is weak and often unclips, resulting in failed prints. ...This piece fits within the opening on the clip to prevent it from unlatching.

This concept is based on a similar design though is compatible with the rubber stoppers provided by SnapMaker for holding work items in place during laser engraving. Unfortunately, it's limited by the laser bed's groove spacing. While each of the...

See [my post in the forum](https://forum.snapmaker.com/t/3dp-part-cooling-fan-5015-replacement/10038/267?u=nivekmai) where I was diagnosing this, make sure your slicer is spitting out the correct gcode before printing, or you're probably going to end...

I wanted to attach standard 4" exhaust ducting to my Snapmaker A350 enclosure so I could use inline duct ventilation fans to exhaust my laser fumes more effectively. This adapter allows a direct connection, and uses the existing holes and screws...

... Internal recirculating air filtration unit coming soon! Check out my ongoing Snapmaker Forums post on the other mods I have on my machine here: https://forum.snapmaker.com/t/cnc-bracing-for-added-rigidity-other-mods/29444?u=elliot

Power supply holder for Snapmaker 2.0 Enclosure (tested on A350 but should work on A150 or A250 too - feedback is appreciated)

I've created a post processor for Fusion 360 for the Snapmaker 2.0 laser module. ... https://github.com/Just3DFun/Snapmaker2.0Laser

Hang this box on your Snapmaker 2.0 Enclosure and put the unused toohead in. ...The box can be installed onto the 48CA beams only.

This is about Snapmaker 2 filament inlet parts. ... As an alternative part of the existing filament inlet, use PC4M6 fitting as PTFE adapter.

Snapmaker 2 Compliant Clamp For Quick and Easy Head Change It's based on the idea of 3D printed compliant mechanisms. ...

Spacer for the column bracket to get a smooth linear movement when using [Snapmaker 2 A350 X-cable guide](https://www.thingiverse.com/thing:4678429).

Based on https://www.thingiverse.com/thing:4417282 Vacuum attachment for Snapmaker 2.0 CNC Height adjustable Attaches to the CNC module with side screws

This is a connector to fit the standard issue Snapmaker 2 exhaust pipe, and connect it to the modular trickle vent exhaust system I have designed. ...(following soon)

Customized with snapmaker writing, and added some additional cut-outs to reduce filament usage. I use this with a tube slid inside ( i bought this as it comes with the correct pipe and end fittings:...

Adapters to connect the Snapmaker bed frame to the linear rail guide supports. This upgrade adds supports at the front and back corners of the bed frame to prevent bending down during actions at the limits of the vertical axis Version 4 will...

This is for a 3.8mm high bed that is just slightly (0.5mm) larger than the Snapmaker bed in all dimensions. Make sure to only adjust inner walls and not outer walls, as adjusting outer walls may cause them to run in to the Z axis rails. ... One...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...

Tested spool brands include: * Snapmaker 1kg * Esun respool 1kg * PrimaValue 1kg To assemble the spool holder, you'll need to acquire: * Ball bearing 608 2Z 8x22x7 mm (available at https://www.remlagret.se/products/608-2z-skf-8x22x7-kullager) *...

After assembling the Snapmaker Enclosure, I realized that the tri-fold doors needed a better way to pull open the doors when they are shut. Came up with this simple door pull that fits the bill and doesn't get in the way of the doors when they fold....

I've uploaded each table below as a Snapmaker Luban project so you can adjust sizes or make any changes you want. The 3 tables are as follows: *Interval - This is just 15 comparisons with the only difference being the fill interval being...

I have had my Snapmaker A250 for about a year and a half now and LOVE it - it meets all my needs in a multi-function machine, yet the handheld touchscreen has always been a bit of a hassle IMHO. I didn't like the limited options for placement, the...

Snampmaker 2.0 spindle Tool head model in step & STL for modelling add-ons/mods

Snampmaker 2.0 Laser Tool head model in step & STL for modelling add-ons/mods

Humans are crafted to produce prints at a precise 0.2 millimeter thickness.

Used pins: - 2mm (dia) Copper audio pins - 2.54mm (dist) round male pins Manual: 1. place EndPart on your diy module wire 2. Remove screws from audio pins, solder power wires through screw hole 3. Solder small 2.54mm pins to data wires 4. Press...