snes controller port 3d models

I created this lid for a friend who lost his, and it's a simple reproduction that was done in about an hour in Solid Edge using only a calliper for measurements. It's not a perfect reproduction, you'll need to sand it after print to make it fit...

I crafted a custom d-pad by hand, meticulously measuring its dimensions with a precision caliper to ensure an exact replica of the original design. ...Despite my best efforts, I detected a minor discrepancy that requires further adjustment for optimal...

**Add something grippy** to the bottom lip of the holder to keep the phone in place. I used a masking tape loop. Might not need **supports**, but I used them. It clips on snug: **very satisfying**. (https://youtu.be/9MN3rmHZccQ) The slvs...

Converts a PCIE slot mounted fan controller knob to fit a serial port slot.

stand for nes/snes controlerssmall prints in about an hour 

There were already some designs out there for NES USB Controller Ports, but they didn't quite Measure Up. So I Got Creative and Remixed the Designs, Crafting One that Would Seamlessly Replace the Existing Port and Allow for a Secure Female USB...

1) the big access hole in the floor helps to run the ribbon/PS wires when removing the printer for cleaning/maintenence 2) I wanted to move the controller out of the enclosure so I could access the SD card while ABS prints cool slowly, side benefit...

I sought to create a stand that could hold my NES Switch controller and 8bitdo SFC30 SNES controller in one convenient place, so I adapted two of Mark's designs to combine them into a single unit. ... Thanks are due to Mark for his original design...

... Pro Controller Mini Wheel" from @pixel2. ... https://www.thingiverse.com/thing:4559213 I edited the frame because i mainly use my controller wired on pc. ... This frame doesn't snap onto the controller, usb cable plugged in is needed to hold properly.

The part didn't fit perfectly for me after I first installed it, after leaving it in the controller overnight it fit much better and the bumpers didn't get stuck. I've been using the controller with this print for about 2 weeks and haven't had any...

I installed a Raspberry Pi into an ATX enclosure, aiming to utilize PS/2 controllers without the USB adapter protruding from the case. ...Conveniently, I discovered a vacant DVD drive bay that could serve as a hiding spot for the converter.

We can't locate the original door, and we're not eager to purchase one, especially when you have to remove it to use Game Cube controllers anyway. So here's my attempt at it. I'm still working on it. ... I just need to figure out how to design the...

... legs of the Skywatcher EQ3-2 (or NEQ3) mount. ... It has been designed a little wider than the original version to fit the "new",handbox controller with ST4 autoguiding port (red controller box, model 20300) inside measurements: 31mm thick, 66mm wide

A well-crafted prototype of a Super Nintendo gamepad is presented in this image.

After a ton of tweaking I think I've finally got a good design. Tree supports are recommend for the best outcome so far. The logo plate will need to be done with .2mm nozzle or at 50% speed with a standard .4 to get the best results. ...You will need...

I am a Text Rewriting Bot, and I will provide rewritten text that meets your requirements. ... Please enter the original text for me to rewrite.

The text is blank, so there's nothing to rewrite.

The printer isn't functioning properly and needs immediate repair to produce high-quality prints.

I needed this for my Nes Pi ;-) http://dcnigma.eu5.org/?p=696

I'm posting this pre-print right now as I print it out. This is a custom top cover for the Wii, something I designed myself after mine suffered damage - the knobs broke off. I based my design on the Gamecube's memory cover and measured everything...

I really needed this for my NES Pi - a unique little device that lets me play classic Nintendo games on my Raspberry Pi!

Remixed to added legends and text. Designed to work with Madmorda's switch cover. ...Printed vertically with tree supports.

With a heat gun set to a scorching 700 degrees Fahrenheit, I encountered significant resistance when attempting to force cheap USB extenders through the original component. ...However, I'm extremely thankful for its thoughtful design and made only minor...

As I worked on this project, I made it my mission to replicate the classic look and feel of the SNES controller. You can see all the behind-the-scenes moments in my Google photo album at https://goo.gl/photos/DuyE2tGNVcjDhsfM6. Here's a list of parts...

Snes keychain, words can be put in the empty area towards the top.

... Entertainment System (SNES) game cartridge, accompanied by a box template to complete the package. ...This combination allows you to enjoy your favorite retro games on the classic SNES console while also having a neat and organized storage solution.

The Super Nintendo, also known as the Super NES or SNES, is a 16-bit home video game console developed by Nintendo. It was released in 1991 and became a major competitor to Sega's Genesis during the 16-bit era of gaming. ...The system featured advanced...

Remote Control for Super Nintendo Entertainment System