snowball mic holder 3d models

This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.

Blue Snowball Mic

Microphone stand for Yeti blue snowball mic. ...I wanted to make it shorter, but the USB cable angles down, so this gives the cable enough clearance, while still lowering the mic under my monitor.

Hey guy today I bring you a simple and yet effective adapter for the SnowBall mic . ...I printed at 50% infill Subscribe to MrJefferson105 Print Settings Printer Brand: Prusa ...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...

The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the mic properly. The part that goes into the mic mounting hole is sized at 15.30 mm and results in a tight fit that needs to...

Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...

... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...

Needed a small form factor pop filter for my snowball mic and i didn't feel like spending 20$ on a few cents worth of plastic, print 2 of the mesh holders, glue a piece of thin fabric/mesh between them before gluing them into the model itself. ... 2...

The Blue Snowball leg joint on the stand is not that strong. Designed in Fusion 360, simply print and screw in the new one. ... 30-40% infill with .2 layer height gives plenty of strength using PLA.

A cord holder for a blue snowball microphone.

mic holder

JUST A QUCK SKETCHUP DESIGN OF A SNOWBALL MOUNT

A simple mic holder to go on a table.

This is a mounting bracket for the Black Ice Snowball to attach to the HP Z24i. You just unscrew the original tripod and screw this on. ... The mic hangs upsidedown from the bottom of the monitor.

it holds the mics to the speaker

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...

The flexable mic support on my helmet intercom broke, this stops the mic hanging by the wire.

... if you use a different adapter, you may need to adjust the size of the socket hole. You can find the Tinkercad files [here](https://www.tinkercad.com/things/aBu5Hy9DaDW-microphone-holder). ...Ungroup the piece, and you can resize the adapter hole.

... ...I put the slot in so it would be flexible and allow for a corded mic. I'm not sure if mics are all the same size, but the holes are 3.5cm and are flexible. *update I altered the design so that it could be screwed in. ...Attached is altered file.

A TABLE BASE FOR MICROPHONES, (FITS MINE FOR VONYX BLUETOOTH SPEAKER MIC). 10% INFILL FOR PARTS. (SUPPORT (EVERYWHERE IN CURA) REQUIRED FOR PRINTING THE BASE INTERIOR). PARTS ADAPTED FROM OTHER THINGIVERSE USERS INCOMPLETE/ MISSING PARTS /INCORRECT...

Made this to keep my Blue Snowball from rolling off the desk and wrecking house. Enjoy! ...Threads made possible by: https://www.thingiverse.com/thing:193647 Print Settings Printer Brand: Printrbot ...

... a standard pop filter with the neck removed, and with slightly longer screws. UPDATE 2/21/2021: Added bracing to pop filter extension, as the old version snapped after continued use. Also made the Mic hole longer to prevent the mic from spinning

... the neck removed, and with slightly longer screws.</p> <p>UPDATE 2/21/2021:</p> <p>Added bracing to pop filter extension, as the old version snapped after continued use. Also made the Mic hole longer to prevent the mic from spinning Category: Audio

This is a simple gadget to attach a Blue Snowball (or other) microphone to a standard "lamp arm" and it also includes a pop filter. The bird is not included :-) Arm_long.stl and ring_center.stl have to be glued together. I've included the...

Snowball from Overwatch

Very simple low desk stand for my snowball microphone.

Snowball from Overwatch. ...Made for a friend for Christmas.

Take advantage of the snow days to play with your children with the snowball creation models. Three types of models of your choice to print. Spanish. Child's play. Snowball fight. Take advantage of the snow days to play with your children with the...