snowboard tip protector 3d models

Spear tip protector for up to 8mm speargun shafts. 

Its a slim tip protector for SQ-D60. ...i printed mine out of tpu A95

This shaft protector works perfect on all different size shafts!! Print in ABS or even better Ninjaflex works out the best. There are like Neptonics Reef protectors but for much less. Keep Spearfishing and divers safe. works on slip-tips too. ... ...

Nitecore TIP buttons protector, GLUED WITH SUPERGLUE. Scratch the contact area (remove the paint) and make it clean for stronger adhesion. Makes strong adhesion and will not fall off. ...

... the tip socket is also broken. This protector aims to prevent this. The magnetic attachment function is retained. Remix of Surface Pen v4 tip cover (2019) by @bearythings **Print at 102%** with Brim. The Fusion360 files are also here. ...

I saw the OG finger protector https://www.thingiverse.com/thing:42441 and wanted something with holes for ventilation. I built it in openscad and made it relatively easy to scale up or down. I added support for differing top and bottom diameters...

I saw the OG finger protector https://www.thingiverse.com/thing:42441 and wanted something with holes for ventilation. I built it in openscad and made it relatively easy to scale up or down. I added support for differing top and bottom diameters to...

Adapted speargun shaft protector to remove some material from 21g down to 12g (to speed up prints). Also added a hole to tie a string, which can be used to attach to float or other places. ...Printed in TPU.

After printing a couple of harry potter wands for the kids I realized that they were quite dangerous and posed a real hazard to their eyes, it was too late to take them away so i printed a couple of rounded protectors, put some blue tack inside and...

A protective shield placed in front of and around the blue tip on the Dillon 1050 primer magazine tube prevents damaged or improperly seated primers in the slide from being drawn back and damaging the blue tip. Never change a blue tip again. For...

The lip that holds the tip on the pencil will require some light sanding/filing in order to slip all the way on and clip around the base of the apple pencil tip. The very top of the model will also require some sanding/filing in order to remove...

So i designed these protectors to cap off the sharp connector ends of the tree. ... It has a little ridge inside to place pressure on the pipe to hold it onto the tree, if it doesnt seem like enough i also have a groove around the outside for a zip...

Additionally, the tail tip was very stable in the center of the device, and the wound wouldn't touch the device walls, which allowed the wound to dry and seal quickly. Unfortunately the cat was slammed the device against a wall very fast and it...

SNOWBOARD

Snowboard

Tip protector for Quest Xpointer Max pinpointer

Safety plug/protector for screwdriver tips. Has a venting hole at the top so you can always pull it off. Fits all 6mm diameter driver shafts. Easy to press on and pull off. Snug fit. The plugs will protect the tips from getting damaged if you...

Only a Snowboard

snowboard the way i want my snowboard to be

A snowboard that says stowe,VT

This is just a simple tip protector for the Bosch Diesel Injectors on my Toyota Yaris Verso. I bought a set of used Injectors, and used this to protect the tip while in storage. ...Pro tip: Put a few drops of carb cleaner inside this to loosen/remove...

Small 4 in. ...snowboard with a camber profile

This is a reversed engineered snowboard. ...the deck was made with a loft.

3d model of a blue snowboard. ...Compatible with 3ds max 2010 or higher and many others.

Protective tip for the Mi6, snug fit

Snowboard that fits Bratz dolls Instructions I sliced this in MakerWare with medium settings. ...Infill: 10% Shell: 2 Layer height: 0.2 Temperature: 230 Extrude speed: 40 mm/s Travel speed: 150 mm/s

A simple protective cap for the Samsung S Pen used with various Samsung Tablets and phones. ... This cap fits snugly around the S-Pen, protecting the fragile S-Pen tip from breakage.

Updated : 6-29-18 Fixed a print imperfection in the model spikes large.stl ( spikes large v2) Please note: The larger tip may not work on some holsters. Mine is worn some so it slides in and out fine. ...Any suggestions or questions please feel fee to...

Updated : 6-29-18 Fixed a print imperfection in the model spikes large.stl ( spikes large v2) Please note: The larger tip may not work on some holsters. Mine is worn some so it slides in and out fine. ...Any suggestions or questions please feel fee to...

This is a cover for the tip of the pedal crank on a bike. This specifically fits a Carbo folding electric bike, but will likely fit a number of other bikes, too. I recommend printing in TPU. ...If printing in PLA or ABS, then you will likely need to...