soundbar mount 3d models
341731 3d models found related to soundbar mount.thingiverse
This helps get the soundbar mounted to the tv so that when the tv is angled with the wall mount, the center channel also moving with it. This should be a good starting point if you have a similar situation for your soundbar and tv. I used the holes...
thingiverse
The clamp is for 35mm and the bar mount is 6mm. Used this for my 15" sound bar for my computer setup so that I could get it off the desk. Easy to adjust in tinkercad for whatever dimensions you may need. ... To get the clamp around the pole, I used a...
prusaprinters
DELL ac511 soundbar mount. DELL ac511 držiak na zvukovú lištu
prusaprinters
Mounts using OEM leg holes and screws. Print instructionsPrint with Prusa Slicer defaults and supports everywhere. In Slicer place one onto print bed, place onto leg support face, place a second object, mirror that one along X axis, place on leg...
thingiverse
This is a mount for a 4in deep soundbar and it goes on a 1in pole I made this for a Rca SoundBar Print Settings Printer: Weistek Ideawerk Rafts: Yes Supports: No Resolution: 0.2 Infill: 20%
thingiverse
This is a bracket to mount a Vizio 38" soundbar (model SB3820-C6) on a Vizio 55" TV (model M55-D0). The mount fits by friction into the vent on the back of the TV. There is a screw hole for the mounting screws on the soundbar. ... Maybe overly...
thingiverse
I purchased a small soundbar for a TV thats used for our treadmill. ...It didnt come with any mounts, so I made these so i could mount it on the wall under the TV.
thingiverse
I wanted to have the soundbar (Samsung HW-M360) mounted under it in order to sound better when the TV gets pulled out and turned to the sides. This probably won't be of any use for anyone else unless you have the exact same model of TV + soundbar as...
thingiverse
Designed this mount to hold a mini soundbar behind the monitor, turning it into a completely hidden, down-firing speaker. The top holes attach to a VESA mount and have a separation of 10cm. The bottom slits are to attach the soundbar using a pair...
prusaprinters
I wanted to have the soundbar (Samsung HW-M360) mounted under it in order to sound better when the TV gets pulled out and turned to the sides. This probably won't be of any use for anyone else unless you have the exact same model of TV + soundbar as...
thingiverse
I added an offset for shorter soundbars. ...Fusion360 file has custom variables for further customizations.
prusaprinters
Designed this bracket, designed to print in a pair, that holds my soundbar across the top of my TV down at a slight angle towards the couch. ...Printed in PETG at 25% infill.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p>...
thingiverse
Pump your beats from the wall with this funkomatic sound bar mount. It's for my old sound bar.. the TV I bought with it (F8000) was murdered by my completely loops ex wife.. that's another story. It sat sad and miserable doing nothing until I...
thingiverse
I created this as I could not find a soundbar mount to fit the top of my Sony television. ... This attaches to the Sony X700E television (TV width: 12mm) This fits the Sony RT-3 sound bar (height: 53mm / width: 70mm)
thingiverse
There was only one other soundbar mount that came close, and that was way too big to fit into the wall mount. It also was too long for the soundbars stock screw. So I designed this for my Samsung Soundbar model HW-H450. It may work on other Samsung...
thingiverse
use this mount to hang the soundbar to almost anything. ... I used M4 screws to hang it up.
thingiverse
Mount to put a soundbar on top of your TV. fits for Blitzwolf SDB1 but will probably fit more models. ... Can be ziptied to your wall mount or screwed to the back of your TV (will probably need some adapters for that)
thingiverse
I made a mount for my soundbar to fit on the wall. Original design had the bar lower, but I had to adjust the TV up a bit on the mount, so the hole on the wall is a little low now. I've included the fusion 360 file so you can adjust if needed. ...
thingiverse
Designed this bracket, designed to print in a pair, that holds my soundbar across the top of my TV down at a slight angle towards the couch. ...Printed in PETG at 25% infill.
thingiverse
Feel free to remix it as it's just a mounting part. ... You can: 1.print this,use some super glue to stick your stuff with the mount part and attach to the monitor 2.design your remix using this as a mounting part
prusaprinters
Feel free to remix it as it's just a mounting part. You can: 1.print this,use some super glue to stick your stuff with the mount part and attach to the monitor 2.design your remix using this as a mounting part Print instructionsCategory: Computer...
thingiverse
these mounts can probably be modified. i made them to fit my older samsung plasma TV so some adjustments would be needed if you wanted to use them for a different TV please download, and post some Makes! ...and if you are so inclined and like the...
thingiverse
-------RCA Soundbar Wall Mount - 81mm wide. Printed on the side using 20% infill. Must print twice. ... 5mm Diameter Screw Holes with Countersink hole of 9mm diameter Back is 9mm off the wall to allow room for cables.
thingiverse
This is a remix of grapedrank's awesome Soundbar TV mount, reconfigured for the dimensions of my Vizio SB3621n soundbar – the dimensions should be exactly the same for the 5.1 version (SB3651n), and the lower part is configured to fit the width of my...
thingiverse
Dell AC511 Usb Soundbar mount for iiyama Monitor
thingiverse
Dell Soundbar Mount to Dell S3423DWC Monitor Adapter
thingiverse
Simple mounting bracket for newer samsung TV leg slots (UE55NU6035KXXC or similar) dimensioned for samsung HW-D350 soundbar. ...