space shuttle launch pad model

it is not a object for a game!!!

I designed this prototype to enable rapid deployment of 250-sized and smaller drones in dense grassy or weed-filled environments. ...Users can easily insert the legs into the ground, securing the device for stability and precise leveling as required.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3LdNv4IHNX2

Printing in an upright position is a straightforward task that requires minimal effort. To achieve optimal results, I suggest setting the perimeter count to three and adjusting the infill density to 20% until the layer thickness reaches approximately...

I designed this launchpad for my Tiny Trainer. The guys over at Fly533 have a "official" one. But it is so big and bulky. This will take approximately 1/3rd of the plastic and time to print. My goals with this were: * LESS PLASTIC *...

You need to print out the same file twice because the file is only half of the launchpad.

This is a versatile foldable launchpad designed specifically for high-performance racer drones, compatible with both X-frames and H-frames configurations, as well as low-battery setups. ... To assemble it, you'll need 5 M3 bolts and 4 M3 nuts on hand.

A little basic 3 component printable stand to hold your firework. It was designed with a 5mm hole on it to fit the basic scream rocket, but of course you can scale it up with the same ratio. ... On the photos the darkened parts are burned from the...

Pretty self-explanatory :)

This is a redesign of a Launchpad I discovered on Thingiverse, accessible via https://www.thingiverse.com/thing:2393056. The original design had the drawback that the arms would gradually slide down over time, so I implemented some knobs to prevent...

The difference with other launchpads out there for drone racing is that this one has 2 holes on the front and 2 holes on the back. The inside of each pillar is void, so you can fill them up with anything that adds weight to them (like sand). ...Enjoy.

Prepare for Lift Off! Conquer the lunar surface with this rocket and gantry system. ...Ideal to be used with the 7TV episode ‘The Moon is Not Enough’ in the 7TV Core Rulebook!Sculpted by Matthew KentContents : -Silo tiles (2 plans) - 15.2cm X...

Finally, if you would like to scale this to fit particular sized transformers you may have, the inner model of the cockpit is provided as Shuttle_ Internal_ForSizing. This can be printed in draft mode so you can get a percentage scaling factor...

Advanced Spacecraft DesignTechnical SpecificationsCrafted with cutting-edge softwareCinema 4D R10.Precise Geometry24024 Polygons28041 VerticesMarket Price $100.00Added to inventory August 21, 2007Product Identification Number:...

A futuristic spaceship materializes out of thin air, boasting remarkable dimensions of seventy-seven millimeters by seventy-eight millimeters by twenty-three millimeters.

Front and Rear Landing Gear

Original design.Rendering made with cinema4dR10.Polygons 28524Vertices 28041

if you guys want to see his other versions here is a link below https://3dwarehouse.sketchup.com/model/81ba92af-e796-411f-a9d2-3c1140de97a2/armageddon-space-shuttle-x-71-almost-like-original# and to david s for his kind and generosity and skill at...

This afternoon, I sought a space shuttle model for printing and discovered one at http://www.thingiverse.com/thing:1966; however, it appeared too smooth. A quick Google search led me to a more suitable 3D gallery model, which I resized and repaired...

This is a different stand for Kmobrain's Space Shuttle model. This one uses far less plastic and is more compact, but still very stable. It is scaled for a 1:100 model (2x Kmobrain's), so if you want 1:200 like the original, you'll have to scale it...

The bottom section is glued to both vertical supports, making it easier to put the Shuttle model on top of the stand. Final update as of May 17, 2022: Version 3 Use of magnets instead of gluing all the components. ...Magnets need to be 2 mm in...

The bottom section is glued to both vertical supports, making it easier to put the Shuttle model on top of the stand. Final update as of May 17, 2022: Version 3 Now you can use magnets instead of glue. All three stand components have perforations...

I'm using 50 mm pins for my model of the Space Shuttle at the ModelStation. ...Feel free to modify this information as needed or reach out to me if the length is incorrect; I'll be happy to adjust it for you, as 50 mm was sufficient in my case.

The Space Shuttle's Solid Rocket Booster (SRB) had an initial prototype, tried out in late '81, with only a single retention post. ...Manufactured by Morton-Thiokol, this design never saw actual flight; instead, it served as a stationary test model...

The original space shuttle with modifications and a stand to allow it to be 3d printed. ...Make sure to scale down.

YOU CAN DOWNLOAD ALL FILES WITH ONE CLICK ON PRINTABLES.COM https://www.printables.com/fr/model/213996-space-shuttle-multi-parts-1200 UPDATES - 30-05-22 : Adding windows after forgetting... FR : J'ai réalisé le Modèle de la Space shuttle à l'échelle...

Custom design for a rail launch system for model rockets. Fits rails that are constructed out of t-slots. This design was created for a TARC model rocket. ...Contains a set of 3 for various tube diameters.

The United States Space Agency's space shuttles featured prominent orbiter vessels, which boasted expansive windows and nose-mounted propulsion systems to enable smoother, more controlled navigation during high-speed re-entry into the Earth's...

The Launch Lug is designed specifically for the Aerotech Arreaux rocket, making it a versatile option for mid-power rockets in general. ...Created using Tinkercad, this model can be edited directly online at https://www.tinkercad.com/things/bIyi23xuDVY