sparkfun screw shield 3d models
336341 3d models found related to sparkfun screw shield.
grabcad
https://www.sparkfun.com/products/15136https://cdn.sparkfun.com/r/600-600/assets/7/d/f/a/c/SparkFun_RTK2_ZED-F9P_Dimensions.jpgublox ZED F9P by Paul THELU u-blox ZED-F9P
prusaprinters
Print instructionsCategory: Electronics Summary An 8020 mount for Sparkfun Qwiic modules using M3 screws. This is for a more permanent usage. This design can mount two of the two hole variety with two of the four hole models or up to four of the four...
prusaprinters
The double set of screw holes in the last position allows for hanging a module off the end so that through hole components do not interfere with the board mounting. Print instructionsCategory: Electronics Summary An 8020 mount for Sparkfun Qwiic...
thingiverse
This is a casing designed specifically for the SparkFun RFID USB Reader model SEN-09963.
prusaprinters
This is an enclosure for the Sparkfun's RFID USB Reader (SEN-09963).
thingiverse
This is a simple case for the SparkFun GPS-RTK-SMA receiver.
thingiverse
... Link to Programmer: https://www.sparkfun.com/products/9825 Link to Light Pipes: https://www.digikey.com/short/qt8z9c - There are many options available; be creative. Just ensure the lens size is 3mm. Any flat #3 or #4 screw will work for assembly.
thingiverse
You will need to print one retaining tabs, which can be found at: https://www.thingiverse.com/thing:3401942 An Din Rail mount for up to four Sparkfun Qwiic modules using M3 screws. This is for a more permanent usage. This design can mount two of...
thingiverse
An 8020 mount for Sparkfun Qwiic modules using M3 screws. This is for a more permanent usage. This design can mount two of the two hole variety with two of the four hole models or up to four of the four hole modules. The double set of screw...
prusaprinters
This is a window or wall mount for the RAK and Sparkfun LoRa antennas, tested with the 90cm long 5.8dbi antennas that can be found here: https://www.sparkfun.com/products/15597...
thingiverse
This is a 35mm DIN rail mounting bracket for the SparkFun Picobuck 3-channel buck converter. Printing: I'd recommend printing it vertically with supports to get the best definition on the DIN profile. We printed with PLA, using 80% infill on...
grabcad
PCB of SparkFun's Qwiic SHIM for Raspberry Pi.Modeling performed in Fusion360 based on the PCB fabrication print found on the product's overview page https://www.sparkfun.com/products/15794
grabcad
PCB of SparkFun's Qwiic SHIM for Raspberry Pi.Modeling performed in Fusion360 based on the PCB fabrication print found on the product's overview page https://www.sparkfun.com/products/15794
thingiverse
This is a window or wall mount for the RAK and Sparkfun LoRa antennas, tested with the 90cm long 5.8dbi antennas that can be found here: https://www.sparkfun.com/products/15597...
thingiverse
... to get the tab from: https://www.thingiverse.com/thing:3401942 to use this part. This bracket is for the Sparkfun quad relay board: https://www.sparkfun.com/products/16833 The second version of the file prints with tapped M3 holes. ...
thingiverse
......This product is available on SparkFun's website, listed as item #13007. To learn more about the GT-511C1R, download its datasheet from SparkFun's server at https://cdn.sparkfun.com/datasheets/Sensors/Biometric/GT-511C1R_datasheet_V1%205_20140312.pdf.