speaker mount 3d models
360721 3d models found related to speaker mount.thingiverse
... by monitors. ...This mount screws into the VESA mount and uses a dovetail joint to support the speaker mount to hold the speaker above the monitor. ...this is sized for a Dell 24" monitor and the speaker mount is setup for Logitech G51 speakers.
cults3d
... by monitors. ...This mount screws into the VESA mount and uses a dovetail joint to support the speaker mount to hold the speaker above the monitor. ...this is sized for a Dell 24" monitor and the speaker mount is setup for Logitech G51 speakers.
thingiverse
Wanted a small compact speaker mount that keeps my speakers as close to the wall as possible. But couldn't find any. So I made this. ...Enjoy :-) The mount keeps the speaker at a 20 degree angle to the wall.
thingiverse
universal speaker mounts for surround sound speakers that use a single m4 bolt to mount, approx 10mm thick where the bolt would pass through, can swivel 180 degrees, has 2 screw holes to mount to wall, can hold a 5+lb speaker with ease when printed...
thingiverse
In the lack of a good speaker foot/mount, I decided to make something original. This is what it ended up being. At first I was a little afraid of the balance, but it turned out great. Easy and straight forwards ;) ...
thingiverse
cylIr is the radius of the speaker cylHole is the opening of the mount holdingRimH is the thickness of the retaining ring holding the speaker in after getting something that fit my speaker, I then tweaked the tabOffset to moving the retaining bumps...
thingiverse
I specifically designed it for mounting the center channel speaker beneath my TV. Part 1 is installed on the back of the speaker at the top. Be sure that whatever screws you use sit flush with the part. Part 2 is attached to the wall using...
thingiverse
Soundcore speaker mount for hanging the speaker against the outside of the shower
thingiverse
I use this speaker mounts to put em at the ceiling. ... check my other designs too ;-)
thingiverse
Traxxas OBA Speaker mount, helpful to attach in non Slash RC models.
thingiverse
Replacement speaker mount for BBC Micro computer accepts a 50mm dia speaker. ...Amended the original design to hold the speaker rather than sticking it to the keyboard PCB
thingiverse
JBL speaker mount for a Cargo bike. ... The raised base make sure that the speaker does not sit in water/snow while riding in poorer conditions.
thingiverse
This is a 4 inch diameter speaker mount I designed for adding some speakers to my car. ...Not pretty, but they won't be seen.
thingiverse
This is a vizio speaker mount that I made for my vizio s5430w-c2 sound bar I realized that this speaker mount works for many vizio soundbars so I though I would upload it. ...If your using a heavy sound bar like I am I recommend you use dry wall achors.
myminifactory
A little mount for little speakers, which is swiveling in two achis. ...Perfectly for souround-speakers. For assembly, you need:2x M4 Screw1x M5 Screw (Speaker Mount)2x dowels and screws (for the wall)
thingiverse
This speaker mount is to be used in the electric car Twizy. You only need to unscrew one screw and click the mount up and screw it on again. I used Speaker JBL GT7-4. ... Enjoy!
thingiverse
This is a simple speaker mount I did up for my Casita trailer. It fits over a 1" (25mm ) belly band and the speaker was a Blue Piston brand. ...This could be used for other things as well
thingiverse
I was unable to find a speaker wall mount for my Wharfedale Diamond 9.0 speakers, so I made one of my own.
thingiverse
This is a speaker mount for the L&R speakers for the Logitech Z625 set. I designed it to be mounted with button head screws in the middle of a 2x4. ...There is a place to zip-tie the cord of the speaker to the mount.
thingiverse
... and holds a 2.25" (57mm) speaker. ... It has three holes (on 25mm PCD) for captive M3 nuts so that you can screw additional things onto the back of the speaker mount. ... You will need glue to retain the speaker.
thingiverse
A speaker mount for the Mandalorian helmet I created. ... Speaker I designed this around: https://www.digikey.com/en/products/detail/soberton-inc/WSP-5008-59/8021830 A cheek joint I designed for the helmet to keep you from breaking the cheeks:...
thingiverse
This is a replacement for a part of the Jamo A410 Speaker Mount. When you have the A410 and you are missing this part, then you know what you are looking for! It's the black circle part in the photo. ...I used two 4x40 screws to mount it to the...
thingiverse
A small and simple, easily adjustable speaker mount for older Bose Tweeters, prints in about an hour and a half and works well. Uses M3 Nuts and Bolts. Designed in 2013 student edition Solid Works. (sorry for the lack of a real photo, don't have a...