speaker port 3d models
44212 3d models found related to speaker port.thingiverse
I designed these speaker ports to help with the sound quality of a diy build I have worked on. There are 2 sets of ports,(3) 2 inch and (3) 3 inch diameter ports at 2", 3", and 3.5" heights. They can be installed using M3 screws or bolts. If you have...
thingiverse
This was used put a screen on exposed speaker bass port so that my kids didn't stick toys in them. After having to disassemble one very expensive subwoofer to remove a toy, I remixed this to fit most common bass ports. Customized version of...
thingiverse
The way this Port hole grill is designed is to be attached with double sided tape or glue, if your speaker has a port tube it wont work, in order to attach to a speaker with a port tube, you need to resize it slightly bigger and delete the 2 outer...
thingiverse
I pulled it and created a port which I could tune to match the characteristics of the box, both internal to the enclosure and extending from the port hole. Each port tube is incremented by 6mm to adjust finely enough to find the ideal tuning of the...
thingiverse
The default settings are for a set of Fostex FE103En enclosures, similar to the ones here: http://diyaudioprojects.com/Speakers/Fostex-FE103En-Bass-Reflex-Speakers/ The external part of the port is built layer-by-layer (with the layer height set in...
prusaprinters
Because my subwoofer is already ported I didn't attempt to mess with port length or any of that and focused instead on smoothing out the airflow as it exited the port. Given that the previous exits had nothing apart from the sharp transition it was...
thingiverse
top side with holes is for mounting 4 holes x4 50mm speakers ask if u like some cad work English or dutch
thingiverse
I've moved this model to cults3d, you can find it here: https://cults3d.com/:1377185
thingiverse
Customized version of http://www.thingiverse.com/thing:112117 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=112117
thingiverse
In replacing the speakers in my Jeep's soundbar, I decided to replace the pair (3.5" tweeter/mid; 6.5" woofer) with a single (5.25" coaxial). In doing so, I removed the 3.5" speaker altogether and wanted to seal it off, to create a better sound...
thingiverse
... tablet and the speakers are lower on the sides. Not sure if anyone else needed the speakers in this area but I shared anyway. Good luck. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6wSJaL0YDAf
thingiverse
The current inset for the usb port printed tight and just file in my few years old Hatchbox translucent PLA but it came out loose using my inland Black PLA. I ended up using a tiny sheet of paper wrapped around the usb port and trimmed it away with...
thingiverse
Compact design speaker box port. specifically designed for a Jeep JK overhead speaker box. This will help with the rattle sound you get with big bass from aftermarket speakers and system. It has a hole in the bottom for a 5mm LED for extra light...
thingiverse
After my first test print, I will be considering adding additional space to insert small strips of foam pad to further surround and insulate the speaker port from vibrations. Instructions See...
thingiverse
Customized version of https://www.thingiverse.com/thing:2896988 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2896988
thingiverse
Customized version of https://www.thingiverse.com/thing:2896988 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2896988
thingiverse
I used supports to print this and had to do a lot of adjustments to get it so that it would not need internal supports inside the left speaker port. ...Be sure to check your system to make sure it does not add supports inside the speaker or you will not...
thingiverse
This is a simple phonestand with speaker ports This phoneholder is designed with a phoncase in mind, but can probably be scaled down to fit the bare model.
thingiverse
This is a phone hanger that fits over the side of a 1x board (3/4") snugly with a charger slot and speaker ports to redirect the sound forward. It's perfect for watching videos in landscape mode while laying on a pillow, especially in a bunk bed with...
thingiverse
This is version 2 of my Icom IC-2AT speaker microphone port cover. Version 2 is made from TPU and goes around the BNC antenna connector. ... The original was made using PLA and can be found here: https://www.thingiverse.com/thing:3736393
thingiverse
This is a repaired version of https://www.thingiverse.com/thing:3515904 It had a problem with meshes not overlapping at the bottom which made the foot too weak. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:5188211 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5188211
thingiverse
It should not be used as a reference speaker is was designed to sound OK for such a small speaker not to be flat and accurate. The design is made so it will print in place with no supports when printed on its side. (DO not print it how the blue...
thingiverse
I ordered the filament (three reels of Prusament PETG, 80€ shipped), and the speakers (30€ for the pair shipped), not to mention the gold plated banana plugs (around 15€ shipped for four pieces) and I wasn't overwhelmed with the results... well, shit...
thingiverse
It is what is says, this Thing can be screwed with M3 Bolts and should be used at the inside of small Speakers only It is supposed to be mounted at the opposite Site of the Speaker(s) Be sure to probably tighten it and prevent Gabs so the Airflow is...
thingiverse
Just a heads up :) This is a spherical ported speaker enclosure that I designed for the Dayton PS95-8 3.5" full range driver. (Link here: http://www.parts-express.com/dayton-audio-ps95-8-3-1-2-point-source-full-range-driver-8-ohm--295-349) I first...