spedix s250 3d models

Since there is not too much space under the Spedix S250 and the the Lens of my Git2 (GoPro clone) camera was touching the ground I needed a lower profile mount bracket. The 2.5mm can be easily taped with M3 and the bracket is a perfect fit. ...I would...

I broke two of the stock landing gear within a few days. I remixed the MHQ2 landing gear to match the stock gear height and to clear the battery mounting plate. This landing gear bolts to the pdb with m3 screws and locknuts. It looks like...

... There are two versions one is 33mm tall and the other gear is 37mm. Choose depending on your battery size / location See http://www.modelhelicopters.co.uk/spedix-s250-quadcopter-arf-kit-cc3d-fpv-racer.html for more informatiion the Spedix Quadcopter

Bobcat S250

Spedix 20A ESC Cover

ESC mount for the Spedix ES30 HV. ... ESC can be found here: https://www.racedayquads.com/products/spedix-30a-esc-hv-3-6s-dshot-600-blheli_s

Reinforced original Spedix S250Q Arm design. ...I can't be the only one who breaks this things...

Spedix 35A ESC protection. It has 2 grooves for cable ties to secure it to quad arms. ...Printed in Sainsmart TPU.

This is a cover for Spedix GS35 ESCs, designed to protect them when mounted to a quadcopter's arm from propeller strike and crashes. ... It has not yet been test printed.

my model lp vehicle for sdhooter game in CryEngine (made in SP) Sniper 3 Ghost Warrior AI controlled only

Pass a weak i bought a spedix 250 and i did broke pards. So i decide to change to carbon fiber body with 3d printing. ...zmr250 is cheap and easy to find the pards .

A replacement arm for a Spedix S250Q quadcopter frame. As many might know, the standard arms break really easy so I designed this replacement arm to get more life out of this frame. Fits right in with the standard screw holes, you might have to drill...

A very rough but operational replacement arm for the discontinued Spedix 250. The front arms are available in Thingiverse but I didn't find a back. Printed and removed a large support area, the part was still very strong and not heavy. Have...

Reverse engineered to detail

Reverse engineered to detail! ...

Appears there are many versions out there but couldn't find anything suitable for my S250-12 power supply. (only about 97mm wide). So, this is my first real 3D design. Not fancy but gets the job done. - Better safe than sorry. Cover simply screws...

A housing to mount a TLV600 CMOS camera in front of a Spedix 250 quadcopter, it prints in two parts: * The main dome-like housing * A cover for the back of the camera For a better fit: * Remove the Spedix 250 front panel * Fit the camera inside the...

This is a simple little plug that fits into the rear holes on the back of a Spedix 250 frame and angles the antennas back at 15 degrees. The hole is perfect for the 3mm drinking straw/coffee stirrer/cocktail straw and provides a cheap and easy way to...

After shooting some video with my aging beater quad it's become clear that I need a more stable, modern platform and this KISS powered Spedix frame is it! This part allows you to easily install and use a standard sized HS1177 camera in the quad...

It is probably slightly heavier Print out of TPU or other Flex material Fits Armattan 30amp ESCs or Spedix 30a .15mm layer height / .2mm should also work fine %15 infill or more if you want them to be stiffer either zip tie it or wrap it with the...

Rough model of my headphone used to create a charging stand.First attempt in Autodesk Inventor 2019

I made this to protect my spedix 20a lite spec esc's.

I made this to protect my spedix 20a lite spec esc's.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/3raqUMioSeH TPU ESC cover, secure with zip ties! ...

This is a 4in1 ECS bottom and top. ...It will fi any 13x27x5 mm ECS, and a 30.5 mm flight controller posts.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/auGijG4dyt1 Print in TPU and zip tie down!

Protect those ESCs from prop strikes and ninja branches! Fits snugly over your ESCs with or without heat-shrink. ...recessed section to keep zip-tie nice and neat.

The Strap Mount has 2mm holes that match the plate included with the Spedix 250 kit. The Hero Strap hangs from the mount with a 3mm bolt with a servo attached to the back of it. ... I specifically sized it for use with the Hitec HS-65HB, but other...

This is a 1/64 (scalable to other scales) scale model of the Joint Light Tactical Vehicle (JLTV) s250 Shelter version, is a United States military (specifically U.S. Army, USSOCOM, and U.S. Marine Corps) program to part-replace the Humvee with a...

Printed this to keep the ESC cool and protect it from prop strikes. ... I used Ninjaflex for the print and it has cable tie recess to stop them slipping off