speed boat rc 3d models
88960 3d models found related to speed boat rc.cults3d
The other problem is the high bow wave which sprays water into the boat. You can avoid it by spray rails. This is not unusual on real boats. ...With both improvements it runs pretty well and I think it is fast enough - at least for me...
thingiverse
... material! The holes are not designed because holes are impossible to print in spiral vase mode. All remaing parts you can take from:http://www.thingiverse.com/thing:284692 (motor boat enlarged)http://www.thingiverse.com/thing:272132 (motor boat)
thingiverse
Boat stand for Speed Boat 3 RC by wersy. ...I've used three 150 x 5 mm aluminium rods with inner M3 thread.
thingiverse
This is a remix of wersy's beautiful Speed Boat 3 RC: https://www.thingiverse.com/thing:930577 Downscaled to half to produce a boat in the same scale as the Joysway Magic Vee, Joysway Magic Cat, Volantex Vector 28 and other micro speed boats equipped...
thingiverse
Hi guys, i uploaded my cockpit for wersy's speed boat, but you must downscale it -20%, because i printed the boat in 120% scale i uploaded the first drive video:https://www.youtube.com/watch?v=WDJn7jVUPNU Hi guys, i posted a new stl file of my...
thingiverse
https://youtu.be/VMiSrvlvjjw Update 08.24.2015 The third try was made with two propellers http://youtu.be/bLIIah6aCVQ https://youtu.be/sKNVVHtIEF8 Update 09.25.2015 A new video from a boat prited in PET by abcona: https://youtu.be/PcmQxUKALkk Update...
myminifactory
https://youtu.be/VMiSrvlvjjw Update 08.24.2015 The third try was made with two propellers http://youtu.be/bLIIah6aCVQ https://youtu.be/sKNVVHtIEF8 Update 09.25.2015 A new video from a boat prited in PET by abcona: https://youtu.be/PcmQxUKALkk Update...
myminifactory
My first speed bootwas enlarged bit by bit of three different parts. This time it should be a hull as if made from one piece with no need of spay rails. Additional it has a deck now to protect electronics. If you seal it with elastic tape and use a...
thingiverse
My first speed boot http://www.thingiverse.com/thing:312235 was enlarged bit by bit of three different parts. This time it should be a hull as if made from one piece with no need of spay rails. Additional it has a deck now to protect electronics. If...
thingiverse
Modified propeller mount for the Speed Boat 3 RC, driven directly by servo. What is required to apply this mod ?: Standard servo - I'm testing with Serwo TowerPro SG-5010. This mod will require modified back deck. 2 M3 screws and nuts Print all...
cults3d
was enlarged bit by bit of three different parts. This time it should be a hull as if made from one piece with no need of spay rails. Additional it has a deck now to protect electronics. If you seal it with elastic tape and use a compensator grommet...
thingiverse
I found Wersy's speed boat 3, and I want to made it for my opinion. Here is the source: https://www.thingiverse.com/thing:930577 Well, I had an old quadcopter, with broken FC, so I want to recycle the other parts for a new project, but now, not...
thingiverse
Version 1: Parts to print: 2x boat_stand_.STL (choose the model for your type of screws) 3x boat_stand_rod.STL (print without supports) Purchased parts: 6x M3 * 10..20mm Version 2: Parts to print: 2x boat_stand_rods_v2.STL 2x boat_stand_base_v2.STL...
cults3d
Parts to print: 2x boat_stand_.STL (choose the model for your type of screws) 3x boat_stand_rod.STL (print without supports) Purchased parts: 6x M3 * 10..20mm
thingiverse
The only part changed is the back half. I changed it to have two motors. I hope to use this controller: https://www.amazon.com/gp/product/B074WLWCLG/ref=ox_sc_act_title_5?smid=A2UB80S6LEB0IV&psc=1 I will hopefully build it this summer. ...When I do I...
prusaprinters
<p>The only part changed is the back half. I changed it to have two motors.</p> <p>I hope to use this controller: https://www.amazon.com/gp/product/B074WLWCLG/ref=ox_sc_act_title_5?smid=A2UB80S6LEB0IV&psc=1</p> <p>I will hopefully build it this...
thingiverse
https://www.thingiverse.com/make:199744 I have modified a BBOne to Z-Achse 900mm (x240 /y240). ...Http://bbone.info Assembled a 3600kV water cooled motor and ESC, but not tested yet.
cults3d
... for epoxying together. There is place for a standard sized RC servo in the rear for rudder control. Space for a 2200mAh 3cell Lipo in the ribbing. Make mods, your own drive system, and please post results! Credits would appreciated. ...:-)
thingiverse
... for epoxying together. There is place for a standard sized RC servo in the rear for rudder control. Space for a 2200mAh 3cell Lipo in the ribbing. Make mods, your own drive system, and please post results! Credits would appreciated. ...:-)
thingiverse
- 2x 30A (or More) Brushless ESC's - 1x 3S LiPo Battery - 1x Standard RC Servo - 1x RC Radio System My boat has a pump-assisted cooling system. It's not really necessary... For Hadware (Recommend all Stainless Steel!!!) : - 1x M4x60 - Rudder -...
thingiverse
WAVE CRUISER RC BOAT V1 ------------------------------------------------------------------------------------------------------------------------ This boat is made for speed on fresh water and salt water. You can mount a simple propeller or a water...
thingiverse
Rudder System for RC boat or speed-boat. ...Works awesome with PLA
grabcad
When I decided to print a boat to be able to use my rc components, I saw the original Speed boat . Made some mods and add a 9gr servo to the Steering wheel . Added a double rudder system with water inlet and outlets. Also made a part to prevent the...
thingiverse
The Century 7004 is a Chinese toy RC boat and can be found on eBay, Alibaba, Dhgate, etc. Its quite fast, and fun but every time I play with it I seem to break the rudder bringing it in to land. £8 per replacement is expensive for sutch a small...