speedlight grid spot 3d models
35772 3d models found related to speedlight grid spot.cults3d
Simple Grid/Snoot for your speedlight (flash). Attaches without any additional bands, straps or magents to most Canon, Nissin, Yongnuo, Godox, Flashpoint, or Neewer speedlights. Others might fit but not tested. ... Concentrates coverage about 10...
thingiverse
I was after a grid for my Canon 580 EXII speedlight, but none of the ones I could buy really appealed to me. They all seem a bit “clunky”, held together with magnets, rubber bands or Velcro. I figured there had to be a neater way. These grids make...
prusaprinters
I figured there had to be a neater way.These grids make use of the bump on the top front of the speedlight to stay secure. They go on easily, they come off easily, and most importantly they stay on when they are supposed to stay on.The Canon 580 EX...
thingiverse
Customized version of http://www.thingiverse.com/thing:476127 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=476127
thingiverse
Grid spot for an Elincrhom Ranger Quadra head, first try, grid not deep enough but it fits fine. Will remix later but then I am going to make another grid to go over the reflector as it will be lower profile for packing. ...Unfortunately it will be too...
thingiverse
For this project I used 12x2 magnets. They are inside of the 3d print. So if you want to print it, you should pause the print, put the magnets and resume it. For the base I used a spring that I found in an old printer. But I am sure that you can find...
thingiverse
Included in this free kit: - Nikon SB800 Speedlight modifer mount - AmazonBasics Speedlight modifier mount - Grid Modifer - Honeycomb Modifier - Triangular Modifier - Wave Modifer - Gel Holder v1 with exposed magnets***NEW*** - Gel Holder v2 with...
thingiverse
Bottom part of Neewer Speedlight NW 565EX, but I'm guessing can work for similar models of Neewer speedlights.
thingiverse
Gridspot set for Elinchrom Ranger Quadra standard reflectors. Angle is changed by length of hex tubes. Optomized for FDM printing. I might try tighter hexagons for a pair to keep them compact. Customized version of...
grabcad
it is just a clamp with hotshoe for mounting a speedlights. ...It fit on every speedlight, except SONY (and others, maded for SONY)!
thingiverse
Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options: word = SPOT
cults3d
round aperture snoot for speedlights, including Canon, Nikon, Yongnuo, Flashpoint, (some) Neewer) Godox. Fits without elastic bands, magnets, etc, by using the common head shape of these popular flashes. ... Other speedlights may work but fitment not...
thingiverse
I really like Scottland's design but needed it to fit my speedlight. ...I also used this model: https://www.thingiverse.com/thing:41157
cults3d
Attaches without any additional bands, straps or magents to most Canon, Nissin, Yongnuo, Godox, Flashpoint, or Neewer speedlights. Others might fit but not tested. Slide this cap completely over the flash head for a light diffusion, or slide out...
thingiverse
I needed something to hold my speedlights and diffuser umbrellas to my tripods, and I didn't like that most things had the flash so far off center from the diffuser umbrella. I had two different kinds of quick releases for two tripods. These mount...
grabcad
This is model of body, witch have attachment of Nikon lenses, slot for Godox TT600 or Godox TT685 speedlights and slot for 36mm positive film. The support fits to mounting plate of NIKON AF-S 70-200 f2.8 VRII lens tripod shoe.It is not FINAL VERSION....
thingiverse
Barn door clip-on for Nikon SB-900 and SB-910 speedlights. Ideal for when you want to use on camera bounce flash and want to ensure that no light hits the subject directly from the actual flash (i.e. use it as a flag). Also great for of camera use to...
thingiverse
I recently bought a set of studio umbrellas and I wanted to mount the flashes by the end of the speedlight instead of the hotshoe. The stand set I had was Neewer brand that comes with 2 silver and 2 white umbrellas. If you're using a different set...
thingiverse
This allowed me to place the speedlight in the oven and light the food inside. I used Velcro straps to secure the flash in the holder. Please note this is not specific for any flash, so both Nikon and cannon fit. its not a snug design in that...
thingiverse
... version. It should fit better. All older versions removed. I have also added vent holes and moved the grid/gel a few mm away from the speedlight fresnel lens as, when a flash is fired in rapid succession, there can be quite a lot of generated heat.
thingiverse
YONGNUO YN560-III Speedlight diffuseur un trouer avec une plaque pour la couleur et u normal YONGNUO YN560-III Speedlight diffuser one whith hole for a plate color and one normal
cults3d
Canon Speedlight 430EX II Flashholder For table or for wall mount. ...For wallmount, use a nailplate 60x60x40x2,5mm
thingiverse
A simple adapter that allows you to transform a softbox for an inexpensive CFL bulb (like the neewer, or Craphy sold on amazon) into a softbox for a speedlight flash. It is a simple E27 adapter on which you can mount a speedlight flash. ... I couldn't...
cults3d
This thing was made with Tinkercad. ... If you like the functionality of the Phottix Varos BG II this is the right alternative! I realized a slightly optimized design for better speedlight usability.
thingiverse
Edit it online https://www.tinkercad.com/things/50V5W5qeSZN You can use this umbrella holder in combination with Speedlights or studio flashes with external power generators. Don't use it with heavy compact studio flashes !!! But anyway: It's your...
thingiverse
This is an enclosure for a Speedlight for use outdoors. It was designed specifically for use in a camera trap situation and was inspired by George S Blonsky's work described in his YouTube video "Making a DSLR Camera Trap for Wildlife Photography...