speeduino 3d models

Speedometer using GPS. Displays trip distance, direction and average speed. Instructions I employed an Arduino DCCduino, Ublox NEO6MV2 GPS receiver, and a 2.4" TFT LCD touch screen display. All sourced from eBay at...

Speeduino compatible small ECU for single cylinder engines

Case for Speeduino V0.4-- using an Ampseal 35 pin connector # 1-776231-5, and brass threaded inserts for 3mm screws to attach end plates.

Box for Speeduino V4.3

... ... Print in default orientation, No supports needed. Added Taller version with cooling vents. 2x M3 Screws with a length between 8-18 will work. The board can be purchased here: https://wtmtronics.com/product/ua4c-for-speeduino-va3-seawolf/

Speeduino NO2C ecu case, super simple to print. ... To secure the board, use a m3 tap in the hole then screw the board with a 25mm M3 hex bolt.

This is an end plate for the hammond enclosure which is included in the BOM of the Speeduino 0.4.3c - should be just as thick as the metal version which comes included. ...

... for it. For the nuts underneath, I used a soldering iron to press them firmly into place - and just so you know, there's an STL file available for spacers that you can use between the Arduino board and Speeduino board when screwing them down.

First take on an enclosure for a Speeduino v0.3.x board is up. The hardware required is four M3x50 cap screws and matching nuts. On December 7, 2016, the design was updated with better alignment and a version of the bottom that includes mounting...

This is a 3d printable enclosure I designed for the Speeduino NO2C ECU. It has mounting points, and has a hole for a DB25 connector, and a hole on the back for the MAP sensor tube (it's been moved by 1mm since the pic, for better alignment). ...

Case for 0.4.3c speeduino board, with space for alternator controller from Westfield MX-5. This is designed to be a drop in replacement for the factory ECU on a MK2.5 Mazda MX-5, this may work for NB variants but this has not been tested as I...

So I needed/wanted a better enclosure for my UA4C speeduino, and a connector capable of more fitment cycles. I bought a Hammond 1455 enclosure (in 103mm width) and some other bits. Unfortunately, I didn't really like the doors that came on the...

Speeduino 0.4.3 case

A printable speeduino badge for your car.

Compact case for the Speeduino 0.4.4d board.

Solidworks file and STL file for a Speeduino trigger/pulse wheel for a Honda Interceptor 500. Was 3D printed in PLA @ 100% infill for test fit. ...Final was made from 4140 steel on a CNC.

Case for the Speeduino 0.4.4d ECU PCM. This is a large case designed for the 2g Eclipse. ...Has cutouts for Bluetooth module and GPS module (or whatever you want to put in them).

designed to hold the speeduino board with the arduino mega attached, uses the pin out board simply screwed to the open end and the cap can be held with a few dabs of glue.

Enclosure for Speeduino 0.4.4.c with Molex 48 pin connector. ... Mount Molex connector with the wide portion to the open side of the enclosure Lid and glue-in screw tabs to come

100% infill

Speeduino is an open source (Hardware and firmware) Engine Management System. I wanted to have a casing for the initial experimental stage where ease of access is more important than robust protection. Note: This casing is specific for...

Case for Speeduino NO2CI am using a DB37 connector - same as the Megasquirt MS1 Extra I am replacing withI used M3 fittings for the lid and DB37There is room in the case for a HC05 - HC06 bluetooth moduleI used an Arduino R3 mount found on here(bolts...

This adapter allows a speeduino mx5 pnp ecu case to be mounted in the car in the standard position using the standard ecu brackets Print in PETG or ABS for heat resistance (PLA not recommended) I used M5 heat set threaded inserts and reused the...

This is a cover for my Molex Connector Adapter that fits perfectly into a Hammond Case, specifically designed to work seamlessly with the Speeduino V0.4 board.\r\n\r\nThe connector adapter board and files can be easily downloaded from this link:...

This is a custom-designed case for the Speeduino V0.3.3 ECU, made from high-quality PLA/PETG/Nylon materials. The case features slide-rail technology, allowing the PCBs to slide smoothly into rails on the inner sides of the case, keeping them snug...

The engineer relies on the Tyco 34 pin Super Seal Male Connector, a trusted component that consistently delivers high-quality performance. ...This robust connector features precision-crafted holes that seamlessly accommodate heat-set M3 threaded inserts...

Here is a rewritten version of the text: Compact housing for the Speeduion NO2C printed circuit board. ...The OBJ and STL files are an exact match.

You will need 4xM3 screws for the caps

A Box For the 4.3c Speedy First File the body alone with no ends, no screw holes or end caps second file is the body no screw holes one end is integrated with the body and it has a hole for the Arduino usb no map hole above it

This is the smallest box I can come up with to house an NO2C with Bluetooth module without using fasteners. The Arduino slides inside the case and then the Bluetooth module slides to the inside of the wall. May have to adjust print speed to get the...