spinny thing 3d models
1389716 3d models found related to spinny thing.thingiverse
It's a spinny thing. With a snowflake in the middle. :D Instructions The smallest ring of the Concentric_02_3rings print pops out easily to be replaced by the snowflake. ...It all prints easily w/o...
pinshape
It's a simple cube with a hole cut through the center for the cylinder to be able to spin.
thingiverse
Customized version of http://www.thingiverse.com/thing:2305259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2305259
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=434613 Instructions Using the following options: letter = p s = 1.04 d = 3.5 height = 5 gravitovectometer_ball_diameter = 7 gravitovectometer = 0 rings = 4
pinshape
However, I decided to upload it as its own thing when I realized it can easily be imported and added to any design or thing anyone wants to make that requires fastening of separate parts with a nut and screw... The part is cool in that the nut is...
cults3d
However, I decided to upload it as its own thing when I realized it can easily be imported and added to any design or thing anyone wants to make that requires fastening of separate parts with a nut and screw... The part is cool in that the nut is...
thingiverse
However, I decided to upload it as its own thing when I realized it can easily be imported and added to any design or thing anyone wants to make that requires fastening of separate parts with a nut and screw... The part is cool in that the nut is...
thingiverse
Just an exercise in engineering. Printing bearings within one piece models. I print this one in ABS at 230 C, raft and support ON. After cleanup, rotate joints carefully at first. Some may be tight depending on your print. Work back and forth to...
cults3d
It was printed at 140 micron (0.14 mm) with 20 degree support on a Zortrax M200 in Cool Grey Z-ABS after being shrunk down to 25% of actuall model size. Modeled after dreadnought kheres pattern cannon, with changes for printability. Used Design...
thingiverse
Another Pen Holder. Print the base with 100% infill for weight, glue a 608(22mx8mmx7mm) skateboard bearing to it and then attach the base and bearing to the pen holder with a little glue and voila you have yourself a spinning pen holder that...
myminifactory
Another Pen Holder. Print the base with 100% infill for weight, glue a 608(22mx8mmx7mm) skateboard bearing to it and then attach the base and bearing to the pen holder with a little glue and voila you have yourself a spinning pen holder that doubles...
thingiverse
This is a fidget toy. It spins, it prints in one piece. It can be very quiet, it can be played with, and provides nice tactile feedback. ...Fidget toys can be useful to aid in concentration, bored, etc so the hands have something to do :)
thingiverse
It was printed at 140 micron (0.14 mm) with 20 degree support on a Zortrax M200 in Cool Grey Z-ABS after being shrunk down to 25% of actuall model size. Modeled after dreadnought kheres pattern cannon, with changes for printability. Used Design...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=188275 Instructions Using the following options: Font = write/Letters.dxf Font_Size = 5.5 Manual_Ring_Size = 18.35 Bands = 2 Knurl_Smoothness = 50 Message = ValvinetYT-Games, Clarinet, and MORE!...
thingiverse
UPDATE, 4 years later: I made the thing and its pegs thicker, to address some fragility problems. Of course there's also the customizable version that someone else remixed from this, if you just want to do that. ... ...
thingiverse
Saw this online a long time ago and decided to make one for myself. ... Never actually made one yet, but here's the files!
thingiverse
Customized version of https://www.thingiverse.com/thing:33945 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=33945
thingiverse
This is a Remix of my favourite spinny fidget, I've printed at least ten for friends and their kids. I wasn't super sold on the middle piece though (too tiny for a good spin) and I thought I might be able to move my interest in fictional logos and...
thingiverse
This Spinny Cube was inspired off from a design I saw on Reddit. That spinner was still in production and I wanted to have it in my hands now. Demo Video The Body: The current body I have made is designed to use 608 Bearings. For printing, I left...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fQVOFGWey8y
thingiverse
Customized version of https://www.thingiverse.com/thing:1182425 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1182425
thingiverse
Customized version of https://www.thingiverse.com/thing:188275 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=188275
thingiverse
Customized version of https://www.thingiverse.com/thing:1182425 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1182425
thingiverse
(4592719 -- you will need good squish settings and good cooling to get it right!). This will be the tops handle/axle. Mate the handle to the base. No glue is needed. Spin it and have fun. ... A great reward for all the hard work fine tuning your 3D...
thingiverse
The openSCAD file (requires Thing:2106, the Doblo factory) can produce the parts for the bearing_test, top, and bottom targets by commenting in and out the last lines. Likely adjustments are: B608_play_outside, B608_play_inside: (more positive...
myminifactory
So this was inspirded by one of my twitch.tv viewers wanted me to Multi Colour print https://www.thingiverse.com/thing:2839576 with my MK2S MMU, so I did and it was is great. But I had thought before I printed it, that each ring would spin on 2...