spool holder 3d print

Left and right piece of a filament spool holder for your 3d printer. Use on a 8 mm thick frame. Use an 8 mm (or less) rod to hold the spool. ...

This is a Spool-holder for the Tevo Flash 3D printer. You will need 4 pieces of 17 x 35 x 10mm steel ball bearings. The spool-holder is adjustable in its width by turning the knob. The bracket that holds the whole spool holder can be inserted from...

Holds all spools of filament, need 4 bearings. ...

Spool holder prusa i3The improvements over the model that comes with the printer are: 1- Give a look to the printer to be smaller. 2- The spool is easier to apply and remove. 3- easier to transport. The stick is removed and can be attached below the...

My bid for 3DPN - 3D Printing Design Contest - Filament Spool Holder!

A very simple desktop spool holder for 3D printer, in only 2 printed parts, nothing to add. For 200mm max spools. ...

files: SpHl-01-4 and SpHl-02-4 for axes with a diameter of 4 mm SpHl-01-5 and SpHl-02-5 for axes with a diameter of 5 mm SpHl-01-6 and SpHl-02-6 for axes with a diameter of 6 mm Printed on 3D Printer Lad-1.0:...

Laser cut or CNC routered filament spool holder for a 3D printer. The design is meant to be cut on 1/2-inch thick material. The photos show laser cut 1/2-inch maple. ...

The one i printed is made for carrying a spool with a diameter of 20 cm (or 8 inches for those who is not european). I got this spool from a regular hardware store and is the kind that usually contains electrical wire. Hardware stores just throw...

Wire Spool holder Spool - D50mm Acrylic rods - D5mm Bonded with UV adhesive - https://goo.gl/cEa98e Butterfly nut - https://goo.gl/VgGK55 - https://www.thingiverse.com/thing:2874671 . ... - Buy & save with cashback ---> http://ali.pub/2v0znm Donate...

They are smaller the normal spools and absorb humidity easily. I also had issues keeping them from unwinding in my setup. So...this was an attempt at rectifying all that - 2 out of 3 ain't bad. Humidity is tough to control. One of the parts...

SummaryAnother spool holder that mounts horizontally (why fight gravity?). This ones fits my UltiMachine 5lb spool, which has a 39mm (1.5 inches) diameter hole. The OpenSCAD file is parametric in case it needs to be adapted for different spool...

A spool holder for Octave brand filament, which is sold on [Amazon](http://www.amazon.com/Octave-1-75mm-Filament-MakerBot-Printer/dp/B0083HSPH2/ref=sr_1_1?ie=UTF8&qid=1379114731&sr=8-1&keywords=octave+filament). Contains a shaft and washer, both with...

(Spool D max 50mm) Мetal rods are taken from the DVD drive. A wire guide is a paper clip. Threaded stud m4 - https://goo.gl/cA3reK or https://goo.gl/hfXNMj Bonded with UV adhesive - https://goo.gl/cEa98e Butterfly nut - https://goo.gl/VgGK55 -...

Assembly Steps Step 1: 3D print the following parts: 4 x bearings --> this should be a good quality print with at least 50% infill. 2 x body 2 x shaft --> You might want to scale this along the long axis if you find the holder too big. The length of...

Disguised as a wall mounted spool holder 3D Printing Guardian watches over the whole 3D printing process. He immediately made our lives easier as now we can replace a spool in seconds. It is especially handy when changing filament for multicolor 3D...

This is a spool holder I have designed for the contest from the 3D Printing Nerd. The holder will hang from the front piece of timber allowing the spool to freely rotate clearing the stored spools behind. ...    

A 3d printed filament spool holder designed for the 3d Printing Nerd Design Challenge. Mounts to his 1x2 filament shelves. Easily snaps onto the front and does not interfere with the rolls of filamen sitting on the shelf. ...Designed in Fusion360.

  The bar part of the spool holder can be varied in length so that Joel can fit different sized spools.       ps. print in pictures wher printed with wrong printer profile and there for not the best quality, my apologies.    There are 4...

A simple spool holder for the smaller Taulman 3D spools. ...

SummarySince not everyone buys a Makerbot Replicator which has nice spool holders, we needed to create a spool holder so that we could leave my Printrbot Jr alone to do its thing. A couple 3D printed parts and 3 Bic pens later, we had our solution!

Makerbot spool holder for the 5lb spool of Ultimachine PLA. ...

This is an alternate design spool holder for the Makergear M2 3d Printer. it works with every spool I have found and i think I have ordered from everyone is seems. The original spool holder design relies on the flange on the spool being in good...

I had previously printed gsterley's Solidoodle Spool Holder Mk2 (thing:97734) and fredhag's wire guide (thing:94675) but needing to carry my S3 around prompted me to create these with the wire guide included. Use a section of 3/4" PVC for the spool...

This derivative includes a few tweaks and notes that I used to make printing and assembly easier as well as a parametric spool holder created in OpenSCAD.InstructionsThe spool currently in my holder has a diameter of 16.5cm and a depth of 9.5cm and...

This is a New design spool holder for the MakerGear M2 Printer. Less stress on filament and x-axis. ...

... suppliers providing a small spool with their 1 Kg filament (approx. ...90 mm x 160 mm diameter with a 35/30 mm hole). I assume these come from Europe or China, anyway, they don't fit on the standard spool holder, so here is an additional one. ...

(Like the 618 nylon 1lb roll) This mod will work on the standard M2 spool holder without modification as well as. This design is retractable so just swing it out of the way when you are not using it. Made with sturdy tri lobe design for added...

Spool Holder for 3D Printing Nerd's spool holder contest. ... I tried to keep the design simple as possible but still carry through the dessign cues of Joel's original shelf brackets.  I have found that some friction between the spool and bracket is...

Spool Holder for 3D Printing Nerd's contest.  Will hold fillament spools by installing to the front of a 1" x 2" wood rail without disturbing a spool directly behind the spool holder. ... A 3D printed screw clamps the spool holder in place.