spool rack wall 3d models

They were taking up valuable counterspace, so I designed these wall mounts for the Dremel brand filament spools. If you know tinkercad, you can easily change the diameter or length of the rod to make it work for your brand of spools. The wall mount...

The Spool Wall Rack was design to help you save space, compared to common wall mount spool supports that orients the spool parallel to the wall. ...Optimised for the best printing quality on FDM Printers, this strong structure Rack doesn't need any...

The Spool Wall Rack was design to help you save space, compared to common wall mount spool supports that orients the spool parallel to the wall. ...Optimised for the best printing quality on FDM Printers, this strong structure Rack doesn't need any...

I converted the Simple Davinci Spool Holder into a Wall Mounted Spool Rack using Tinkercad. This gives me an easy way to store my extra filament spools on the wall above my printers. The design was printed at 50% fill and 0.4 layer height on my Stock...

I converted the Simple Davinci Spool Holder into a Wall Mounted Spool Rack using Tinkercad. This gives me an easy way to store my extra filament spools on the wall above my printers. The design was printed at 50% fill and 0.4 layer height on my Stock...

SummaryI converted the Simple Davinci Spool Holder into a Wall Mounted Spool Rack using Tinkercad. This gives me an easy way to store my extra filament spools on the wall above my printers. The design was printed at 50% fill and 0.4 layer height on...

For now, wall mounting is the easiest and I ended up on this design: http://www.thingiverse.com/thing:119920. I found it to be overkill structurally even after trimming away most of the volume. I also found this one:...

I was sick of having all my filaments spool around and my printers room is pretty small so I decided to design this bracket so I can store them up in a corner. It works great with 1kg spools but if you want to use bigger ones let me know and the...

I was sick of having all my filaments spool around and my printers room is pretty small so I decided to design this bracket so I can store them up in a corner.It works great with 1kg spools but if you want to use bigger ones let me know and the...

I designed this wire spool rack to use 1/2" conduit cut to whatever length you need for the spools you want to hold. I cut mine to 18", mounting the parts 16 1/2" apart. Providing enough extra on the end to keep them in place. ...All of my wire...

I created this after looking over MothersOfInvention - Filament spool holder https://www.thingiverse.com/thing:3139782 and Atu's - Wall Mounted Spool Holder (Stronger version)...

... 55 mm (rounded head).InstructionsJust slide 2 pipes into side holders and mount it on the wall.Mount for spool holder is optional. If you want to use it, dismount original Prusa spool holder from the printer frame and slide it into wall rack holder.

Print a pair of these brackets and set a standard Schedule 40 3/4" diameter PVC pipe on them for a simple and strong wall-mounted spool holder. The spacing between the brackets and PVC pipe length are your choice. Schedule 40 3/4" pipe is about 1.06...

Spool Roller for Hatchbox Tabletop Wall Mount Rack Yes, this is yet another spool roller specifically for the Hatchbox Tabletop Wall Mount Rack. These are attached to your filament spool prior to being used with the rack to give an easier rolling...

When measuring up for your own rack, mine is 600mm, I have one centre support piece @ 300mm, but I think 200mm centres would be better, minimum clearance from above is also 200mm, this is measured from the top surface to the top right angle corner...

3 tiered rack for storing and organizing filament spools.

Rack for filament spools, designed to be used with 5/8 dowels.

... left side. ... Basic wall mounted rack for my 1kg spools. These use 3/4" EMT conduit from the hardware store. Can either be anchored to studs or as I did with plastic drywall anchors. ... I found the strongest rated anchors I could, I think 50lbs.

... a further set and it will stack on top of one another! Using this, I no longer need to mount individual spools to the printer, I can pull the filament down straight in the extruder from the spool rack making it much easier to swap out filaments.

Reconstructed the spool rack to fit a pipe of 22.5mm diameter. ...While I was at it, I redesigned the upper screw hole for improved accessibility and to fit M5 wood screws with a countersunk head.

Designed this for filament spool storage. If you want a tool tray that will hold scissors, screw drivers, cutters, etc. then download the left and right. ...If you just want the support bracket with no tool tray, then you only need the right side and...

WALL RACK

##Wall Rack Simple wall rack to hold mugs, spices, and whatnot: it lowers the search penalty and keeps things in order. Has depth of 11.5 cm. Print 1 left arm and 1 right arm per rack. ###Materials needed per rack: * \#8 plastic wall anchors,...

A rack for hanging stuff on the wall. Expandable. ... If you print the v2 top at .2mm layer height, the layer changes add some detail to the flower.

A rack for hanging stuff on the wall.  Expandable. ...   If you print the v2 top at .2mm layer height, the layer changes add some detail to the flower.

A rack for hanging stuff on the wall. Expandable. ... If you print the v2 top at .2mm layer height, the layer changes add some detail to the flower.

This is for all of you guys out there. ...I use them for my Tattoo machines on the wall. ...yu can use it for whatever you want :)

... Download includes files in 6 different sizes to fit a variety of bike tires. Approximate print time 11 hours. We recommend printing in PLA. You'll also need four 5-6mm bolts and nuts to attach to the wall. ...Will hold a bike up to about 14kg/30lbs.

Spool Rack 96 inches

At my old house, I mounted them to the wall, but I don't want to put so many holes in the wall at my new place. These mount by putting an M6 nut in each slot on the side of the model. Then to secure it to the rack, an M6x12 bolt with washer will...