spool rods 3d models
108870 3d models found related to spool rods.thingiverse
A parametric universal spool adapter for use with threaded rod and two nuts. Included stl fits M8 rod and nuts, and spools with a hole diameter of 4-8cm. ...No need for supports.
thingiverse
This is a filament spool holder for a 8mm rod The diameter is 54mm The white pieces printed while the spool was without the attachments, the black pieces after I installed the spool holders.
thingiverse
Filament spool adapters for using with 8mm rod. ... You must fix the adapter with a nut or similar as shown in the picture Tappo.stl: 55.8mm diameter Tappo-sunlu.stl for Sunlu filament spool: 56mm diameter Tappo-sunlu-v2.stl for Sunlu filement spool;...
thingiverse
*You need* Threaded 8mm rod (Not mandatory but suggested) 4x8mm bolts to make sure the threaded rod stays on place Anet a8 printer *Instructions* Print 2 of those Place one on the left side of the lcd and one on the right side of the lcd Place your...
myminifactory
... the same closet/shower rod for holding spools? It gets even trickier. This design enables the use of the closet/shower rod AND allows you to easily switch out a spool. ... The spool of filament in the photos is from 3Dom USA: http://www.3domusa.com
thingiverse
... the same closet/shower rod for holding spools? It gets even trickier. This design enables the use of the closet/shower rod AND allows you to easily switch out a spool. ... The spool of filament in the photos is from 3Dom USA: http://www.3domusa.com
thingiverse
Had trouble with some narrow spools moving within my spool holder so I made this rod from mike_mattala brilliant customizer. I then made some tapered nuts to securely hold the spool. https://www.thingiverse.com/thing:2658755 Customized version of...
thingiverse
munckychris made an awesome spool holder, but I was too lazy to go buy a PVC rod. STL and STEP files attached for a three piece rod. Part is cut into three parts because the middle section is almost full z18 z-height. ...Rod side pieces screw into...
thingiverse
This is my lure retaining line spool for the Black Widow Rod that I use for my kayak setup when trolling for crappie. ... ► Bekith Rod Holders → https://amzn.to/2SnBXfM ► B'n'M 13' Black Widow Crappie Rig → http://bit.ly/2S39b56 ► Video Link →...
thingiverse
No bearings, no threads, just the spool wheel with an 8mm hole in the centre to slide right onto an 8mm threaded rod. ... This remix (if you can even call it that) just reduces the heightof the spool wheel from 40mm to 30mm so that two can be used with...
thingiverse
After getting frustrated with the time that it took to use the conventional, two-piece spool holders that were inserted into both sides of the filament spool, I decided to design this one-piece spool roller. It has now made my task of changing...
thingiverse
Based on "Very Strong Trinus Spool Holder (4 parts)" by Sylvian42 I wanted to use 8mm threaded rod with a universal spool holder and SKT CAP screws, I liked this design, so I have made a similar version using Inventor. Fixings: 6x M3x10 SKT CAP...
thingiverse
This is a Line spool designed for spinning rod sold at DAISO(JAPAN). Other materials : washers larger than M4 (I used JIS small M8, as in the picture). The object is placed up side down in the STL file. Because the plastic plate for drag...
thingiverse
This very simple spool holder bracket was designed to hold my filament rolls, by mounting a length of 20mm HDPE pipe, inside a plastic box (to protect the filament from moisture). I went for this design because it was simple, and used HDPE pipe...
thingiverse
Spool holder. ... No bearing required. Smoothrod length is up to you. I'm using 25cm smoothrod. can hold up to 3 spool Please post your makes and likes will be much appreciated. ...
thingiverse
No support needed, this uses my Z rod fix, just use 2 16mm M3 screws and nuts to secure it to the rods. "Core" diameter is 30mm down to around 65mm. Good for 3mm or 1.75mm filament, depending on what you use on your 1405. NOTE: This will work...
myminifactory
... without any support. It's fraction fitted and some force might to be need to put it together. The 3way PVC connector is an addon. The cable spool fits onto the connector nicely. ... https://www.youtube.com/watch?v=PUQeGrOBy8s (in Hungarian)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=735213 Instructions Using the following options: wall = 2.7 chamfer_depth = 5 height = 15 inner_diameter_backlash = 1 spool_diameter = 51 number_of_arms = 5 arm_compression = 1 arm_thickness =...
prusaprinters
<p>Hallo,</p><p>hier ein kleiner Halter für ein Schrank, Kommode woran man eine 16 mm Stange aufhängen kann. </p><p>LG</p>
thingiverse
The Printrbot Simple Metal Spool Holder http://www.thingiverse.com/thing:322923 required the use of PVC piping to build. Being that I didn't want to head out to a store and do any cutting. I decided to print the rods up. This allows for really nice...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=431426 Instructions Using the following options: height = 7 diameter = 32 rod_diameter = 9 leg_count = 3 leg_thickness = 3 overall_height = 20
thingiverse
A simple spool holder using 1/4" threaded rod, 1/4" -20 nuts, R4zz bearings and some washers. ...Adjustable to the width of the spool.
thingiverse
###Top Mounted Spool Holder A top mounted spool holder for the Anet A8 using the **stock threaded rod**. It replaces the spacers in between the LCD screen and the back plate. ...It is the same width as the spacers and the M3 screws work with this part.
thingiverse
By having an excess of M8 and M6 Threaded rods and few gear bearing laying around I decided to make them hold big spool of filament. ... --------------------- You need : 1 pcs - m6x250mm 2 pcs - m8x165mm 4 pcs - m8x200 8 pcs - m8 nut +10 pcs - m6 nut +2...
thingiverse
Recommend this for filament pass through https://www.thingiverse.com/thing:3397576 And this for holding a humidity sensor in the box https://www.thingiverse.com/thing:3394439 I used a 44 quart ziplock weather-shield storage box, which gave me 16" of...
thingiverse
... solid acrylic or wood rods. You can print it yourself here, or if you have trouble finding the acrylic (or don't have the equipment to cut it right) this FT-5 spool holder is also for sale on my website with all of the parts ready to go. ...
thingiverse
I modified the genius spool holder design for Black Widow from bdwalker1 to fit a M8 rod. ...The 2nd part is the "Parametric universal spool holder" by rowokii: http://www.thingiverse.com/thing:767317 I just used flanged 608 bearings instead of normal...
thingiverse
This filament guide is made for the "Quick Change spool holder": https://www.thingiverse.com/thing:2625942 and this one: https://www.thingiverse.com/thing:2625942 Took the mounting ring from: https://www.thingiverse.com/thing:2456844 ....and made it...
thingiverse
I've included pictures of the common Closet rod spool holder on Thingiverse that I originally printed out (the Clear filament one) to compare with my design (Red filament one). While the one I printed from here was nice and I surely appreciate...
thingiverse
I like to use the spool hubs that can be found [HERE](https://www.thingiverse.com/thing:605360) and I needed a way to mount this on the D-Bot. This is a simple mounting block that will require two nuts to secure the 8mm threaded rod. ** UPDATE -**...