spring loaded card holder 3d models

this hasn't been tested yet

Needed Hardware 4 springs Compression Spring, 1.375" Long, 0.36" OD, 0.296" ID 5 M3 screws

The cards are wood veneer on cardstock so I was worried about throwing them in my backpack without a holder. It should be able to hold other square cards of the same size as well. It uses a snap fit joint so no screws or glue are required, but you...

Spring Loaded Phone Holder

spring loaded tool holder for 1/8 engraving bits, I plan to use for engraving glass bottle surface. ...Any experience with such a tool?

A spring loaded pen holder that mounts in aluminum extrusion. The spring makes up for uneven surfaces and the pen takes an easier ride. Made specifically for paper mate flair pens. Design files are Alibre type. ...

This is a spring loaded sponge holder with an ability to wick using one hand. The idea is to have the dish soap bottle sitting vertically and to feed through the bottom opening in the sponge holder. By pushing in the sponge with one hand will allow...

... at a local hardware store. But some different sizes of springs could successfully be used and may fit your needs better. So experiment!   Spring Loaded Phone Holder by ChaosCoreTech is licensed under the Creative Commons - Attributionlicense. ...  

This is a 3D printed phone holder that has a couple springs on the back that help it clamp securely onto just about any size of smart phone. There are also screw holes on the bottom to allow it to mount to different objects. I included a mic stand...

This is a 3D printed phone holder that has a couple springs on the back that help it clamp securely onto just about any size of smart phone. There are also screw holes on the bottom to allow it to mount to different objects. I included a mic stand...

Check out the video here: https://youtu.be/qNqM_ocIJ-0 This is a 3D printed phone holder that has a couple springs on the back that help it clamp securely onto just about any size of smart phone. There are also screw holes on the bottom to allow it...

This device uses a commonly found ballpoint pen cartridge and spring to a make a spring-loaded pen holder.

It's like DaDa art in the bathroom... ...marvel at this 3d printed spring loaded bog roll holder.

Replacement for spring loaded toilet paper holder. Width: approx. ...110-135 mm For spring with outer diameter smaller than Ø20 mm and a lenght of about 40 mm (no load)

It's like DaDa art in the bathroom... ...marvel at this 3d printed spring loaded bog roll holder. ... Instructions Printed with PLA.

Here is a simple and functional magnetic spring loaded PCB holder. It looks nice and minimalistic, and is very usefull not only for PCBs. ... All you need is: - M3 x 30mm screw - Ballpoint pen spring (usually about 25mm - 30mm) - magnet with 6mm...

Here is a simple and functional magnetic spring loaded PCB holder. It looks nice and minimalistic, and is very usefull not only for PCBs. ... All you need is: - M3 x 30mm screw - Ballpoint pen spring (usually about 25mm - 30mm) - magnet with 6mm...

Spring loaded pen holder for a MPCNC mount uses a M4 x 20 screw and hex nut to hold the pen in place the spring is a 12mm O.D. light weight spring to keep constant pressure on the pen tip on the media Best for Pens with a 8mm diameter barrel. ...the...

Spring-loaded pen holder for pens with a max. diameter of 11mm. The mounting points are designed to work with my Kress/AMB spindle mount: https://www.thingiverse.com/thing:4663262 Additionally necessary: 3 x M3 threaded inserts 3 x long M3 screws 3...

Spring loaded tea bag dispenser Should fit ~25 tea bags Designed for tea bags that are 70x80mm or smaller

Simple spring loaded quarter holder to use in car, office, or whatever. For US Quarters. I needed something to hold bunch of quarters for a car wash, that would be fast to load and unload (dump all at once), and wouldn't rattle on the potholes. It...

Kitchen Roll holder has a spring-loaded push pin/ball that's pretty satisfying to use Needs only 2 springs ± 20mm long and 9-10mm wide with an inner diameter of a minimum of 7.5mm and a maximum outer diameter of 10mm also added a (No Holes) Version...

This is an improved variant of this compost bag holder.https://www.printables.com/model/120150-compost-bag-holderThe spring function hold the bags against the wall so that they can not fall out by mistake.I printed it in PETG, 5 Perimeters & 0%...

One of the pictures shows how to assemble but:tap the holder hole with the M5 screw and the bottom of the body with the M6 screwput the M6 screw through the bottom of the holder and then the spring over the excess of the screw hanging out the...

put the M6 screw through the bottom of the holder and then the spring over the excess of the screw hanging out the bottom 3. put the holder into the body and screw the M6 screw through until the hole in the holder is visible at the top of the slot in...

... I'd make the files available to fellow tinkers. I've tried several springs. Seems the .390in radius fits the best. In terms of force, somewhere between just holding the PCBs and breaking the fixture should due. :-) Happy building. ...Bill

For assembly you will need: 4 - [M4 x 10 socket head cap screws](https://amzn.to/2SFaIfG) 2 - [M4 nuts](https://amzn.to/2LQUiht) 1 - [Sharpie marker](https://amzn.to/2SzLTlf) Edit: You should remove the pen holder from the mount when you are not...

This was heavily inspired by and is essentially a remix this thing by DieZopfe: https://www.thingiverse.com/thing:4694593 Car mounted phone holder (spring loaded) === I couldn't find a phone holder that had a spring loaded clasp/clamp, so I decided...

A slightly modified version of my previous model (spring loaded tool holder). Added presure adjustment of the tool using a set screw above the spring. ...Of course you need to adjust the tension before mounting the holder which is not very practical but...

Car CD mounted spring loaded adjustable tablet holder, should fit 4" to about 7" tablet. Print orientation is as the pictures show. Use a 1/4 x 20 x 1 1/2 in socket head bolt and a 1/4 x 20 nut for the knob. The spring is a 3" tension type...